How long should iPhone 6 be charged for the first time? Which smartphone charges the fastest? How it works

Last week, a story became popular on the Internet, the heroes of which were an unknown Internet user and Apple's senior vice president of software, Craig Federighi. The first sent a letter to the head of the corporation, Tim Cook, in which he asked whether it was necessary to remove tasks from the list of running applications in order to save battery power. “No and no again,” Federighi answered for his boss on his own Twitter.

Soon after this, foreign and domestic media began publishing a link to a special section on the Apple website, which talks about how to increase the operating time of an iOS device without recharging and extend the overall life of the built-in battery.

The page that has gained new popularity notes that the term “lifetime” in relation to a battery means exactly the period that elapses between two charges, and the definition of “lifespan” implies the time after which the battery needs to be replaced with a new one. Exactly how to extend both - translated by RG Digital.

1. Apple advises updating software promptly, as updates often include new energy-saving technologies.

2. You should avoid too high and too low temperatures when using gadgets - this applies to tablets, smartphones, and laptops. The range of comfortable temperatures is from 16 to 22 degrees Celsius, the upper limit is 35 degrees Celsius. Charging at higher temperatures may cause permanent battery damage. Use in cold conditions may reduce battery life, but this is temporary.

3. Remove cases from devices while charging. This will help them avoid overheating as charging can cause excess heat.

4. Keep gadgets half charged if you leave them for a long time. A completely discharged battery may completely lose the ability to charge in the future. In turn, a battery charged at 100 percent for a long time may lose some of its capacity. It is recommended to store devices at a temperature not exceeding 32 degrees.

5. For iPhone and iPad, there are additional ways to increase battery life. The first is to set automatic brightness, in which the device adapts to lighting conditions. The second is to keep Wi-Fi on all the time, since this access method consumes less energy.

6. iOS 9 introduced a power saving mode that warns the user when the battery is low and also reduces power consumption by disabling iCloud synchronization and AirDrop data transfer. At the same time, the ability to make calls, send SMS and access the Internet will remain. When the device is charged, the saving mode is automatically turned off.

7. According to Apple, iOS 9 has become the most energy-efficient operating system, since it has the ability to find out which applications are using the most battery power. If desired, the user can limit the background activity of the most "gluttonous" programs.

I absolutely welcome you! The question (voiced in the title of the article) is, on the one hand, quite interesting and thought-provoking, but on the other hand... What is there to think about? After all, in essence, the answer will be very simple - you insert the charger and charge it! How can this be done wrong?

It would seem that we could end here, however... there are a huge number of related nuances regarding proper charging of the iPhone. How to charge without damaging the battery? What is possible and what is not? What to do after purchase - wait for the discharge or use it immediately? Now we will figure it all out! But first, let's remember one very simple truth - the battery cannot be charged incorrectly. What a surprise! :)

This is simply not possible due to the fact that:

• Wire.
• iPhone.
• Power supply.

There are special controllers responsible for the process of receiving current. If one of them doesn’t like something, the device simply won’t charge. Of course, it is necessary to make a reservation that we are talking about original accessories. In “Chinese” ones for 100 rubles there can be no talk of any microcontrollers. And although they are not originals, it is better not to use them for a long time, but only in desperate situations.

The only thing that can be done correctly or incorrectly while charging is not to cover the device with a blanket, pillow or other materials. Because the iPhone, and most other gadgets on the market, tend to heat up while charging (). And it’s safer when this heat escapes freely into the atmosphere.

How to charge an iPhone for the first time after purchase?

As you wish. Devices go on sale already with a certain charge level, so it can be used almost immediately and without any restrictions.

If we talk about the fact that for the first time, before using it, you first need to completely discharge the device, then fully charge it, and “that’s all about it.” Here it should be noted that modern lithium-ion batteries do not have the so-called “memory effect”, so there is no need for all these procedures. Plus, their service life, as a rule, is about 500 such cycles - and this, for a second, is 2 years. And only after that they will begin to more or less seriously lose capacity.

The conclusion is this: we bought it and use it freely.

How long does it take to charge an iPhone?

The correct answer is as much as he needs. Moreover, the speed at which the battery will be filled with energy depends on many conditions:

• The choice of power supply unit is important. By the way, I safely use the adapter from the iPad () - it turns out really faster.
• Whether the device is being used while charging or not. It’s clear that if you play a game and charge at the same time, the process may take longer.
• Even the length of the wire matters!

If we talk about charging time from 0 to 100%, then for an iPhone (depending on the model) it may take from 1.5 to 3 hours. Naturally, the “plus” iPhone 6 and 6S take the longest to charge. Simply due to the fact that they have a more capacious battery. This is more of a guideline; yours may be a little more or less. about the charging time of each model and whether you need to pay much attention to it?

In cases where deviations from this “norm” are large enough, read this article again. You may be doing something wrong. Although problems with the battery cannot be ruled out, you cannot do without a service center.

Finally, a few more useful tips that Apple publishes for proper charging and maintaining battery capacity:

1. Apple recommends removing cases while charging, as they cause heat, which in turn negatively affects battery capacity.
2. For the same reason, you should not use the device in the cold.
3. If you want to put your iPhone in temporary storage, it’s better to charge it halfway, turn it off, and then safely put it away for a long time.
4. Only original accessories. Yes, it is important. By the way, it is not necessary to use cables and power supplies from Apple; it is enough that they are simply certified. You can identify them by the inscription MFI (Made For iPhone) on the box.

In general, it should be noted that all of them, except the last point, are purely advisory in nature.

And even if it doesn’t, there’s nothing wrong with that and the battery won’t immediately deteriorate. Again, these are just recommendations and it is up to you to decide whether to follow them or not.

Finally, let's summarize. It doesn’t matter how or what you charge your iPhone with, the main thing is to do it with quality accessories and follow some safety precautions. And everything else, with minor reservations, can be ignored.

P.S. Do you think the same? Feel free to “like” and click on the social media buttons! Don't agree? Do you have any questions? Write in the comments!

Every owner of a new car is firmly convinced that he knows almost everything about it. After all, having become the owner of such an expensive branded gadget, you want to fully enjoy all its sophisticated features. But such a trivial question: how to properly charge an iPhone may cause slight surprise and even bewilderment for many users. Well, what could be simpler and more understandable than this procedure - insert the charger into the iPhone and connect it to the network. At first glance, there is nothing complicated in this process. Can regular charging harm an electronic gadget? But in fact, there are a huge number of different nuances that affect the quality and speed of charging, and are also responsible for the durability and condition of the battery.

Recharging the iPhone battery

The battery is the heart of any mobile electronic device. And in order for it to last as long as possible, not only from recharging to recharging, but also until its resource is completely exhausted, you need to know how many times and how correctly it is recommended to charge the iPhone. Neglecting all these tips and rules, gadget owners may be faced with the need to change faulty branded batteries too often. Moreover, replace them with new, and not always good quality, analogues. And I must admit, this is not a cheap pleasure.

One part of users charges their electronic devices almost every day. Others, on the contrary, resort to this procedure only after the battery is completely discharged. One way or another, all owners gadgets want only one thing - for their device to always be active and not fail at the most crucial moment. But how to find that golden mean so that the battery lasts a long time, and the user saves himself from the need to constantly recharge it. Experts recommend: in order for the battery to last as long as possible, it should neither be charged to 100% maximum nor discharged to zero. The most optimal charge level is considered to be from 40% to 80%.

The influence of chargers on the battery condition

The correct charging of the iPhone 7 is influenced not only by competent and orderly actions of the user, but also by the quality of the power supply, network adapter and USB cable. Every owner of an Apple gadget should know that to recharge the battery, you need to use only original equipment from the manufacturer. The thing is that branded chargers are equipped with special microcontrollers that monitor the process of receiving current. And if the charging conditions go beyond acceptable limits, for example, the temperature rises, the voltage jumps or the current drops, then the battery simply stops charging.

In network adapters and power supplies from unknown manufacturers, there can be no talk of any microcontroller. Therefore, such devices must be used very carefully, only in the most desperate situations and for a fairly short time. Otherwise, such an adapter can not only burn out the power controller in the iPhone 7 itself, but also completely damage the battery.

Charging a newly purchased iPhone 7

All electronic devices that hit store shelves already have a certain level of charge. Therefore, a newly purchased iPhone 7 can be used immediately, without any additional actions or restrictions. And the myth that you need to charge a new gadget for 72 hours the first time and then completely discharge it is unfounded. The thing is that modern iPhones use new generation lithium-ion batteries. They, unlike conventional nickel batteries, do not have a full charge memory effect, so there is no point in doing this procedure with new Apple devices.

But despite the fact that the new iPhone, although it has a small charge of energy, it doesn’t care The first charge is required, which is also the most important. It is this that lays the foundation for the future uninterrupted and long-term operation of the gadget. It is worth noting that the first charging of iPhone 7 is no fundamentally different from recharging previous models. The initial charging cycle for iPhones of almost all models consists of the following simple steps:

• The iPhone is connected to the charger for 3 hours;
• after the battery is 100% charged, you need to use the iPhone until it is completely discharged;
• connect the charger for another 2 hours and do not use any gadget applications;
• bring the charge up to 100% again and then you can fully work with the device.

Once the battery is fully charged, the controller that is built into the iPhone automatically turns off the power supply. It is he who tries to charge the battery as soon as possible and prevent it from overcharging.

Optimal charging time for iPhones

In principle, there are no clearly established boundaries defining the charging time of iPhones. The gadget will be connected to the network exactly as much as it needs to gain the required amount of energy charge. And this depends on a number of factors:

• iPhone discharge depth;
• temperature conditions - considered optimal is from 16 to 22 °C;
• availability of an original or certified charger;
• wire length;
• using the gadget during the charging process.

If we approach it purely theoretically, then it may take from one and a half to three hours to recharge the battery from 0% to 100%. Here everything will depend on the device model and battery parameters. It is clear that the iPhone 7 will take longer to charge than all its predecessors. And all because it has the most capacitive battery, which not only draws more power from the gadget, but also lasts 2 hours longer than the batteries installed on previous iPhone models.

You can learn how to charge the iPhone 7 by studying the instructions that come with any new gadget. In it, Apple experts give several important tips and recommendations that will help not only use your battery economically, but also extend its service life. Among the most important recommendations are:

• Use only branded or certified equipment for charging;
• You cannot charge the iPhone while it is in a case or covered with any object, this can cause the device to become very hot, which will negatively affect the battery itself;
• It is not recommended to use the gadget in severe frost;
• if the device will not be used temporarily, then before turning it off and hiding it, its battery must be charged 50%;

You can extend your battery life by lowering the screen brightness and disabling rarely used apps and programs. However, it is up to the user to decide whether to follow these tips or not. After all, they are all purely advisory in nature. And if for some reason you need to turn on your iPhone during the cold season, this does not mean that the battery will immediately fail. The main thing is to use only original chargers and follow safety precautions. And everything else, albeit with small reservations, can be ignored, of course, to the detriment of the battery’s durability.

Most often, when comparing several top smartphones, users analyze the battery life of the device. However, sometimes the deciding factor can be the charging time of the smartphone. For example, if the device’s battery is low and you only have 15 minutes to recharge it. During this time, each flagship can receive a different amount of energy. One of the foreign publications decided to conduct a test on the charging speed of smartphones in order to identify the fastest charging phone.

The following people took part in the test: Asus Zenfone 2, Google Nexus 6, OnePlus 2, Samsung Galaxy S6, LG G4, Motorola Droid Turbo, Apple iPhone 6. First, all phones were completely discharged until they turned off, then charged to the 5% mark. After that, several “races” were organized for gadgets. The point was to analyze how many percent the device will charge in 5 minutes, starting from the 5% mark. Then for 15 and 30 minutes. After this, we compared the charging time to 80% and to 100%. Here's what we found out during the experiment.

• Charge level in percentage after 5 minutes (starting from 5%)

Asus Zenfone 2 noticeably pulled away from the rest in the first five minutes. During this time, he managed to charge 17%. The minimum figure was for the iPhone 6: the device was charged only 6%. The remaining participants have an average of 11.43%.

• Charge level in percentage after 15 minutes

In this race, the leader was again Asus Zenfone 2. Its figure reached 32%. At the same time, the Samsung Galaxy S6, which was previously in the middle, jumped to second position. The iPhone 6 was again in the back rows - last place. It has the same score as OnePlus 2.

• Charge level in percentage after 30 minutes

At the thirtieth minute, the Samsung Galaxy S6 caught up with the main leader, Asus Zenfone 2. In half an hour, they were charged by 53% - that’s a little more than half. iPhone 6 took the second to last position - 36%.

• 80% charge

In the fourth race, the Samsung Galaxy S6 took the lead. It took him 48 minutes to reach the 80% mark. This is the only phone that takes less than an hour to charge to 80%. For comparison, the iPhone 6 took a little over an hour - 1 hour 15 minutes.

What to do if your iPhone doesn’t see the charger? Owners of Apple-branded equipment sometimes encounter a problem when the iPhone does not see charging or charges intermittently. If the problem was caused by improper operation, then it can be solved at home, otherwise you will have to seek the help of specialists. However, manufacturing defects in devices from this company are rare.

What to do if the iPhone does not charge depends on the type of malfunction. Among the most common reasons is a breakdown of the adapter or battery. To exclude them, you need to replace the battery or connect the device to another charger. If this does not help, you should pay attention to the condition of the smartphone.

So why doesn't my iPhone respond to charging? In most cases, the problem is with the connector. The item may be damaged as a result of:

• contamination of contacts;
• mechanical impact (impact, cable rupture, etc.).

Do not rule out a faulty cable or software glitches due to which the signal does not reach the power controller. In this case, charging the iPhone may even be dangerous for the adapter, since it is not designed to transfer current “in vain”. Despite the reliability of Apple technology, it is easy to damage, so any unsuccessful action can lead to failure.

What to do if your iPhone doesn’t see the charger?

The entire range of iPhones (5, 6, 7, 8, X, SE) of recent years have the same charging problems. In most cases, they can be solved using standard methods: cleaning the connector, reinstalling iOS, or replacing the battery. In addition, the malfunction may be caused by a broken cable or adapter.

The lower blocks will contain the most common solutions for fixing charging problems. To avoid many difficulties that arise during the operation of a smartphone, you need to use original chargers, connect the adapter to a stable power supply and handle the cable carefully.

Connector dirty

The iPhone sometimes does not see charging due to contamination of the port contacts with lint, dust, etc. due to improper storage conditions. Cleaning should be done using a wooden toothpick in a circular motion around the perimeter of the hole. The main thing is not to lower the toothpick too deep so as not to damage the iPhone charging connector.

In addition, it happens that USB on the computer does not work. The sockets supply a voltage of 5 V (0.5 A), which is not enough to charge the iPhone normally, since the gadget requires 2 A. Therefore, only original adapters should be used for the device.

iPhone doesn't charge well due to firmware glitch

Often the device does not see the original charger due to incorrect operation of the OS. Without the appropriate command from the operating system, the current supplied to the connector will not flow to the battery, so it will seem that the gadget does not recognize the adapter at all. There are several ways to fix the charging situation:

• hard restart (press the Home and Power buttons at the same time for 15 seconds), on iPhone 7 the volume and Power button, on iPhone 8 and X, quickly press the up button and release, then down and hold Power;
• calibrating the battery using third-party software or completely discharging it.

If none of this helps and the iPhone is not charging, all that remains is to do it. You can download the official version of iOS from Internet resources relevant to computer topics. However, if the iPhone does not see charging after reinstalling the OS, you should look for another cause of the problem.

Read also:

Replacing a faulty battery

Apple devices are not designed for self-repair and replacement of elements, so their design is more complex than that of other smartphones. But when the iPhone starts charging incorrectly due to a faulty battery, you have to resort to emergency measures. To disassemble a smartphone at home, you will need:

• screwdrivers: small pentagonal, flat, Phillips, spatula (depending on the device model);
• sucker;
• tweezers.

The following signs indicate that the battery needs to be replaced:

• the battery does not hold a charge;
• The iPhone only works from the network;
• physical deformation of the battery has occurred;
• The smartphone does not see charging, etc.

An approximate procedure will be given here, since for the latest models of the device the instructions are slightly different:

1. Unscrew the screws on the end of the housing. Move the cover away from you, pry it up and remove it.
2. Place the iPhone face down on a soft cloth and unscrew the screw holding the cable connector using a Phillips screwdriver.
3. Warm up the area where the battery is located with a hairdryer or other available means to 40-50 °C. This is necessary to soften the glue holding the battery in place.
4. Pull the “tab” under the battery, then pry it up with a flat-head screwdriver and remove the faulty battery completely.
5. Replace the element and assemble the iPhone according to the given algorithm.

In most cases, this solution to the problem is almost universal, since often the iPhone does not see charging due to a faulty battery. However, the steps described above are only suitable for iPhones up to the 4th generation. For others, the instructions become more complicated, since you need to remove the screen to gain access to the “stuffing” of the gadget.

It is not recommended to disassemble the iPhone 5(s) yourself if you have problems with charging, as it has additional difficulties with the Home button. It is attached by a cable to the motherboard, so careless actions when replacing the battery can damage the gadget even more.

In the case of an iPhone 6 (and higher) that does not see charging, you can handle it on your own:

1. Unscrew the screws on the end of the device and lift the screen 90°. Remove the holder (fastened with 5 Phillips screws) and bend the tabs of the cable.
2. Unscrew the battery cable holder (2 screws).
3. Remove the cable and then the battery by pulling the adhesive stickers and prying off the battery with a screwdriver.
4. Insert another battery and assemble the device.