What can be done from a GPS navigator. Homemade GPS navigator based on Arduino (3 photos). Getting to know Garmin Mobile XT

For many fans, fishing is not even a hobby, but a way of life to which they are ready and even devote all their free time.

And therefore, very often, avid fishermen have to invent and make various baits, spoons, tackles and much more themselves.

DIY silicone baits

It is often a pity to part with a vibrating tail that has already served its purpose. Or would like to add some element to it that you think is quite necessary. It doesn’t matter, you can make a new silicone bait at home.

Manufacturing:

1. In a used canning jar, cleanly washed, of a suitable size, we dilute the plaster to the state of thick “bazaar” sour cream and dip old vibrating tails into it halfway to obtain a template. After the solution has hardened, carefully remove them. If you want to make changes to the shape of future products, use a sharp knife to add the necessary touches before pouring the silicone.
2. Lubricate the finished cleaned form generously with fat, most suitable option sunflower oil, so that the finished products are damaged when taken out and do not stick to the mold.
3. All further steps of pouring silicone into molds must be done in the open air. he or in a well-ventilated area.
4. We cut old unused silicone products into pieces and place them in a jar, heating them on the stove.. To prevent the silicone from burning, it must be stirred. Keep the fire at a distance of 15-20 cm from the heated container. To obtain silicones of various colors, food coloring is added to it and, if desired, you can drop a little of a special fish flavor purchased at a fishing store.
5. The heated and thoroughly mixed silicone mass is poured into the mold starting from the thinnest point. If you are making a two-color bait, then the layer of the second color is poured only after the first has dried.
6. After complete hardening (usually 15-20 minutes), the bait is carefully removed from the plaster mold We. We clean the mold from silicone residues, correct the oil layer and repeat the process.

Mini-fastener for quick change of attachment with your own hands

Very often when fishing, especially fly fishing or lure fishing, there is a need to quickly change the nozzle. It was invented for this purpose special form mini clasp. It is quite simple and easy to make at home.

Manufacturing:

1. Tools needed to create a mini clasp:

• Wire cutters.
• Small round nose pliers and pliers.
• Tweezers.

1. A thin, rigid wire is used as the base material.. An acceptable option is a large staple from a regular stapler.
2. We bend it with pliers into a product according to the shape, resembling a paper clip, but reduced in size by half.
3. We bite off the excess wire.
4. We select the size of the camber rick (hard silicone tube) of such a size that it fits tightly around the fabricated fastener.
5. Using wire cutters, bite off a piece of the tube slightly longer than the fastener, it will act as a retainer.
6. We thread the resulting piece of tube onto a fishing line and firmly fix it with a knot.
7. Insert the attachment you need into the other side of the fastener.
8. Pulls the silicone cambric with force. That's it, the mini clasp is ready.

Feeder for feeding fish from a boat

If you prefer to fish from a boat, then you will definitely be intrigued by this very simple and inexpensive fish feeder. It will serve as an excellent replacement for casting bait by hand, especially if fishing is in the current.

To make it you will need:

• a piece of sewer plastic pipe;
• two plugs for it;
• lead;
• electric drill;
• rope, rivets;
• loop and lock.

A piece of pipe about 30 cm long is fitted with plugs on both sides, one firmly and tightly, the other like a window in a house on a hinge.

We drill holes along the entire surface of the feeder.

A rope is connected to the opening lid, and a lock is attached to it from the inside. Weights are installed outside the pipe near the cover.

The feeder, pre-filled with bait, is carefully lowered into the selected fishing spot with the lid down due to the weights attached to it, and with a slight tug of the rope the unwanted spot is emptied. The whole place is baited and you can fish.

Wobbler from a home workshop

Store-bought wobblers are certainly not bad: very colorful, streamlined, completely imitating a small fish and its movements in the water, but they have one big drawback - the high price.

Therefore, many people prefer to make them themselves at home, especially since the process itself does not require special equipment and is quite exciting in itself.

Making wobblers:

1. First of all, we draw on paper a sketch of what we want to do. Regardless of the material used to make the wobbler, it must be made of two symmetrical halves to pass a steel wire amplifier inside it.
2. Wobblers can be made from foam plastic. It is easy to process, but less durable than plastic or wood. Having decided on the material, we cut out the blanks.
3. We make fastenings for rings and tee hooks from thin stainless wire, we install them in the grooves cut in advance in the halves of the wobbler body, and fasten them with glue. After the glue has dried, we make a cut for the front blade and secure it firmly with glue.
4. Then we ship the wobbler. There are many options here - everyone does this procedure specifically based on their personal preferences. That is, we customize it for ourselves.
5. Fill the remaining empty spaces on the surface of the wobbler with epoxy resin and grind. You can now begin the creative process of priming and then painting the wobbler. There is nothing holding back your imagination here.

DIY spinner

Making a spinner with your own hands is not at all difficult with some skill. An example is a spinner.

For this you will need:

• regular paper clip;
• hook tee;
• metal plate 0.5 - 1 mm (can be taken from an empty tin can);
• small bead;
• a piece of sheet lead;
• tools: pliers, file, scissors, needle files.

We cut out the shape of the petal itself from cardboard and transfer it to metal. Carefully cut along the contour and remove burrs along the edges with a file.

We drill two holes along the edges and process them with a needle file.

We bend the places with holes at an angle of 90° relative to the petal.

We make an axle out of wire with a ring and a loop at one end, where we attach the tee hook.

We thread a petal through the other end, then a bead, and at the end we make a loop for the fishing line at a distance so that the lead sinker does not interfere with the free rotation of the petal.

The spoon is loaded experimentally on a reservoir by attaching weights to the niche between the petal and the tee. AND finishing touch– spinner color.

Homemade products for summer fishing

When fishing, the problem of using live bait for bait often arises. Catching it usually involves wasting time. In hot weather, baitfish quickly become lethargic in a bucket of water and die.

A very simple device made from two plastic bottles will help you solve this problem:

1. Cut off the neck of a two-liter plastic bottle by half.
2. Then, on the same side, cut off the neck of the bottle at the widest part.
3. You have a truncated cone, somewhat reminiscent of a watering can.
4. We cut off the bottom of it.
5. For the second bottle, cut off the bottom 5-7 cm from the point where the largest diameter appears.
6. We connect the structure together. We insert the neck at the place of the cut, but on the contrary with a small hole inward and firmly fasten it with threads and a needle. We tightly place the bottom from another bottle onto the cut off bottom according to the principle of a drawing tube.
7. We attach a small sinker in the middle of the side of the bottle, and a rope on the opposite side.

That's it, the trap is ready. We throw bread crumbs inside and throw a trap near the shore. The fry, having swam for food, can no longer get out of there on their own.

All that remains, when you need live bait, is to pull the trap out of the water and, by removing the plug at the bottom, get fresh and vigorous live bait.

How to catch more fish?

I have been active fishing for quite some time and have found many ways to improve the bite. And here are the most effective:

1. . Attracts fish in cold and warm water with the help of pheromones included in the composition and stimulates its appetite. It’s a pity that Rosprirodnadzor wants to impose a ban on its sale.
2. More sensitive gear. Reviews and instructions for other types of gear can be found on the pages of my website.
3. Lures using pheromones.

You can get the rest of the secrets of successful fishing for free by reading my other materials on the site.

Homemade products for winter fishing

In winter, live bait is often used to catch predators.

An example of such a budget and quickly manufactured gear:

1. Material for production – sewer PVC pipe with a diameter of 32 mm. We cut the pipe into pieces of 10 - 15 cm.
2. We process the chamfers at the ends of the pipe with a file.
3. Using a heated nail, burn 3 holes in the tube. Two on one side, opposite each other, for hanging it on a tripod and one with a diameter of 1 mm on the other side, for stopping the fishing line.
4. We make a line stopper in the shape of the letter P and thread it through a small hole. It should not interfere with the free movement of the fishing line.
5. We make a ring (suspension) from a thick 0.4-0.5 mm fishing line, passing it through two holes on a plastic pipe. The suspension is used to attach the pole to a rod firmly driven into the ice, so that an overly frisky fish does not drag your pole under the ice.
6. We wind up to 10 meters of main fishing line onto the pipe.
7. At the end we put an olive weight and a tee hook on a double loop.

That's it, the girder is ready for work.

Tip: wrap the end of the pipe near the suspension loop with red tape and then the disappearance of the girder will be visible from afar, and you will always have time to get to it in case of a bite.

Homemade products for do-it-yourself fishing for crucian carp

There is one bait that crucian carp, especially not very large ones, prefer over all others. This is ordinary semolina porridge, but prepared in a special way.

Semolina bait recipe (hot):

• pour water into a saucepan, add a couple of drops of flavoring and bring the mixture to a boil;
• pour the cereal into a saucepan in a thin stream, stirring continuously until a homogeneous thick mass is obtained;
• turn off the heat and leave the porridge to cool and steam at the same time;
• when it reaches an acceptable temperature, knead it thoroughly with your hands to achieve even greater density;
• to minimize drying of the porridge, wrap it in several layers of gauze;
• You can’t wrap porridge in plastic; it suffocates and turns sour very quickly.

This kind of porridge makes good balls for bait on a hook.

Semolina bait recipe (cold):

• pour water from a reservoir into a tin can, drip a little flavoring;
• stirring constantly, add semolina there;
• We continue the process until a homogeneous mass is formed. The thickness is checked as follows: raise the spoon with the porridge above the jar, if it remains on the spoon and does not fall down, the porridge is ready;
• set the porridge aside for 10 minutes to swell;
• We take a pre-prepared syringe and fill it with the mixture.

The bait is squeezed out of the syringe onto the hook and wrapped around it in a circle, the hook tip being closed last.

DIY fishing crafts for feeder

When feeder fishing, the feeder is consumables. It breaks while casting, it gets snagged and a new feeder is needed. In order not to constantly buy new ones, you can make them yourself from scrap materials.

Feeder made from a plastic bottle:

1. We take an ordinary plastic bottle (preferably green), cut off its neck and bottom.
2. We mark the resulting plastic and then cut it with scissors into rectangles measuring 6*13 cm.
3. We roll the finished pieces into a cylinder with an overlap of 1 cm and fix them with a stationery stapler.
4. On the side surface of the feeder we attach a piece of sheet lead with a loop made of a regular paper clip attached to it.
5. Using a heated small soldering iron, we burn holes in the feeder in a checkerboard pattern at a distance of 2 cm from each other.
6. Insert a swivel into the resulting loop.

That's it, the feeder is ready, you can start fishing.

As you probably already understood yourself, there is nothing complicated in making additional homemade fishing devices and, for the most part, they do not require any specific skills or expensive machines for their production.

Therefore, do not be afraid of this, act boldly, invent little things yourself that can simplify the process of fishing or increase the catchability of the gear, and simply while away the long winter evenings.

How long has it been since you had a really BIG CATCH?

When was the last time you caught dozens of HUGE pike/carp/bream?

We always want to get results from fishing - to catch not three perch, but ten kilogram pikes - what a catch! Each of us dreams of this, but not everyone can do it.

A good catch can be achieved (and we know this) thanks to good bait.

It can be prepared at home or bought in fishing stores. But stores are expensive, and to prepare bait at home, you need to spend a lot of time, and, to be fair, homemade bait does not always work well.

You know that disappointment when you buy bait or prepare it at home and only catch three or four bass?

So maybe it’s time to use a truly working product, the effectiveness of which has been proven both scientifically and in practice on the rivers and ponds of Russia?

It gives the same result that we cannot achieve on our own, especially since it is cheap, which distinguishes it from other means and there is no need to spend time on production - you order it, it’s delivered and you’re good to go!

Of course, it is better to try once than to hear a thousand times. Moreover, now is the season! This is a great bonus when ordering!

Find out more about the bait!

For a professional fisherman, making fishing tackle with your own hands is an activity that brings the same pleasure as fishing. By creating new gear, feeders, baits and other devices, a fisherman can increase the fish catch several times. For making tackle at home, improvised means and tools are excellent.

Making fishing tackle is a fascinating activity.

If a fisherman makes fishing devices with his own hands, he must use the following materials and tools in his creativity:

1. Wood. From wood, a fisherman may need planks and bars. The wood is excellent for wobblers and poppers.
2. Metal plates. Petals for spinners can be made from this material.
3. Wire. Can be used as mounts and rings for baits.
4. Hammer.
5. Saw.
6. Sandpaper.
7. File.
8. Materials for covering tackle and other devices (varnish, paint).

To make a fishing device with your own hands, it is enough to have available tools and materials.

Helicopter tackle is a popular winter tackle.

The helicopter structure consists of the following elements:

1. Hard spinner.
2. Long leash.
3. Short leash with hooks.
4. Retaining ring.
5. Sliding sinker.
6. Main line.
7. Fixing cambric.
8. Reel, necessary for attaching all the gear.
9. Bite alarm.

Making fishing gear is very simple. Helicopter gear is made from tin. Thin tin cans are perfect.

The diameter of the pinwheel reaches five centimeters and it is attached to a leash, the length of which is one and a half meters, and the diameter is 0.22-0.25 millimeters.

Four short leashes of 15 centimeters each, 0.15-0.2 millimeters wide, are mounted to the long leash. Fastening can be done using a swivel. Place hooks on leashes. The leashes are attached at the same distance from each other.

The leashes are attached to the main line with a diameter of up to 0.45 millimeters with a locking ring. A flat weight weighing up to 80 grams is mounted on the fishing line.

Place a cambric up to four centimeters long and up to half a centimeter in diameter just above the load. The cambric fixes the fishing line on the whip, which notifies the fisherman about a bite.

Willow branches are placed under the whip, which can be collected on the river along the shore.
Before fishing with a helicopter, the fisherman must drill a hole in the direction of the current at an angle.

The hole is cleared of ice and fishing gear is installed:

• a pre-bent pinwheel is passed into the hole. It is necessary to bend it so that it plays better in the water and has resistance to fast flow;
• the bait is placed on the hooks, and the assembled tackle is lowered completely into the water;
• after reaching the bottom load, the cambric should be pulled and secured at the end of the whip, which should be located at the hole;
• the excess fishing line is wound on the reel. It should be next to the whip.

Having made a helicopter with his own hands, a fisherman will be able to fish constantly in winter and catch big fish.

To make a wobbler yourself, you should take wood from deciduous trees. The optimal length of oval wood is five centimeters.

We assemble the wobbler with our own hands:

1. A one and a half centimeter block should be cut from the wood.
2. Draw a wobbler fish on the resulting block.
3. Trim the excess wood along the contour with a knife.
4. Make a mark with a pencil in the front part of the future wobbler, and then cut out a cavity to create a blade. Cut the belly along the length of the bait. A fastener made of stainless wire will be inserted into this place.
5. Insert wire in the form of rings into the intended place and fill with epoxy glue.
6. Apply varnish to the finished wobbler. Once the varnish has dried, hang treble hooks on the workpiece.
7. Adjustment of the level of buoyancy must be done using lead weights, which are attached to the holes in the abdomen between the nasal and abdominal loops.
8. Sand the bait and re-varnish it with a waterproof effect.
9. Next, prepare a blade from aluminum cans, which should be glued into the wobbler.

By following the instructions for making a wobbler, you can get an excellent specimen, which will later be used to equip a fishing rod.

DIY mandula

How to assemble a mandula? You can make a mandula from polyurethane foam. The material is obtained from various rugs and women's slippers. Mandula is great for pike perch fishing.
For the mandula you will need multi-colored polyurethane foam, double or triple hooks, wire 0.5-0.7 mm wide, a cotton swab, red wool, pliers, pliers, wire cutters, an awl, highly water-resistant glue, and a knife.

Method for preparing mandula:

• cut polyurethane foam into cubes;
• stack the cubes on top of each other and coat the layers with glue;
• burn the center of the structure with a hot awl;
• the structure should be made cone-shaped using a knife. The awl should remain in the plates;
• a cotton swab is mounted in one of the cones;
• Take the pliers and make a loop at the end of the wire. The other end is attached to the hook;
• the prepared cone is placed on the hook;
• A fly is tied from red wool with glue. While the product is drying, a polyurethane foam plate is put on the second hook to make it more buoyant;
• all structures must be assembled together by twisting wire.

It is possible to make a mandula from polyurethane foam. With such equipment it is excellent to catch a predator.

Such baits are also called spoons. To make a spinner, you will need a cross-shaped hammer with balls at the end, a wooden board with a recess in the middle, a rubberized steel shaft, a metal ball, a drill, a hacksaw, and a steel stylus.

Stages of creating an oscillator petal:

1. Make a petal template on cardboard.
2. Make a contour on a one and a half millimeter sheet of metal using a stylus according to the template.
3. Clamp the sheet and cut out the petal according to the template with a hacksaw.
4. Fix the workpiece in the recess of the board.
5. Remove uneven areas along the edges and make holes for the rings.

Manual vibrators are made of metal and wood. Simple design will allow you to catch excellent fish.

Making a spinner spoon

The spinner frame is made of stainless steel wire. Its length must be at least one hundred millimeters and its diameter 0.8 millimeters.

Manufacturing stages:

1. The curvature of the wire is removed with pliers, slings or chawls.
2. The petal is made from 0.33 liter aluminum cans. Due to the softness of aluminum, it can be cut with scissors.
3. Make holes on the wire with a thick needle to secure the petals.
4. Assembly. One end of the wire is twisted into a ring with pliers. Then a bead and a petal are put on. The structure is secured with another bead.

You can increase the weight of the spinner by choosing a long wire, as well as using a sinker with a hole.

It is better to make a spinner out of wire. It is subsequently weighted with a sinker.

To make a castmaster you will need an empty metal pipe with a cross-section of sixteen millimeters and lead.

The tools you will need are a hacksaw, a drill, a drill up to three millimeters, a file, a vice, a caliper, and a soldering iron.

Let's assemble the castmaster ourselves:

• the pipe is clamped into a jaw and the workpiece is sawed off. The cutting angle must correspond to the original castmaster and measurement angle;
• make holes in the centers of both ends of the workpiece;
• tin the workpiece from the inside so that the lead does not fall out;
• seal the holes with masking tape and let it dry;
• Close the remaining holes with molten tin. For this stage you will need a soldering iron;
• process with sandpaper and drill lead through the holes in the pipe.

A castmaster is made from a small hollow tube. You should work with lead carefully, as it emits fumes that are harmful to health.

DIY balancer

Such a balancer may be needed when fishing in winter. It looks like a voluminous bait that looks like a fish.

Manufacturing stages:

1. It is created from light metal alloys.
2. The hooks are attached to the head or tail of the workpiece, the sharp end should point upward.
3. Two loops are attached to the back and belly of the bait. The first is necessary for the fishing line, and the second for the threesome.

A balancer is a piece of equipment that looks like a fish and is used in winter. Homemade balancers guarantee a good catch.

Foam rubber is prepared in the form of fish from foam rubber sponges of different colors.

Manufacturing stages:

• Before starting work, you should wet and squeeze out the sponge;
• then a fish measuring 3-8 centimeters is cut out;
• can be attached to jigs without glue;
• If you want to attach a treble hook to the bait, you need to make a cut, and then insert the hook and secure it with water-repellent glue.

To make your own accessories, you may also need a dishwashing sponge. It is used to make foam fish that can attract a large school of fish.

Mormyshki at home

For jigs you will need lead or lead-tin alloys and gypsum. You should prepare the jig in the fresh air or wearing a mask, as lead is toxic.

Manufacturing stages:

1. Create a plaster mold. Pour plaster into a matchbox and place a jig in the middle.
2. After the plaster has dried, the jig is removed. The mold is cleaned and channels are created for pouring tin.

The jig is the simplest bait that is very easy to make yourself. It is necessary to prepare plaster and mold.

DIY bite alarms

To create an alarm electronic format You will need a bicycle spoke, electronic and bite alarms with a rod mount.

Manufacturing stages:

1. Attach the spoke to the signal roller.
2. On the other side, a barrel is secured.
3. The resulting alarm is mounted on the rod stand.

You can also make bite alarms yourself. The basis is a bicycle spoke and a commercial signaling device.

To catch fish with a float rod, artificial baits are required that imitate crustaceans, worms, and maggots.

For good fishing, the bait must have an attractive smell to the fish.

Aromatic drops are often used:

• anise;
• vanilla;
• garlic.

As bait, you can use wet and dry flies made from wool, feathers, cork, polystyrene foam, and colored threads.

To prepare fishing tackle at home, it is enough to use available materials: wooden blocks, polystyrene foam, wool, feathers, threads, and so on. Before making homemade products, you should understand what it will look like in the future and what kind of fish can be caught with it. Properly made tackle will help the angler catch a great catch.

Fishing has long ceased to be a simple entertainment and hobby; for many men, this is the time when they can relax, take a break from problems and focus on a complex but interesting process, and homemade fishing tools for summer fishing will help with this. Therefore, there are a great many ways to fish, as well as varieties of fishing tackle, everyone selects them to suit their own needs, and some even create several home-made fishing products for summer fishing. This could be a simple hand-made wooden stick with fishing line and worms, or a high-tech novelty, complemented by your own spinners and modern baits for predatory fish.

• Types of homemade products
• Spoon
• Float

And it doesn’t matter how you prefer to fish: the old fashioned way or using modern gadgets - a homemade fishing device for summer fishing will help you adjust a ready-made device to your requirements. Since ancient times, fishermen had to make everything themselves, and even in the modern world, many experienced people prefer to rely on equipment they created themselves, which will never fail, unlike purchased ones.

This practice is common because factory production is set up to create crafts that will suit as many situations as possible, and with rare exceptions they do not take into account many details.

So, what can you do yourself to make summer fishing easier if you are new to this activity?
No matter how developed your imagination is and no matter how varied your DIY fishing gear may look, they can still be classified into one of 8 main types:

• a spoon is one of the most necessary things when fishing on a river;
• feeder - helps you not to bother with additional feeding;
• A float is the main gear that will help you understand whether the fish has eaten the bait along with the hook. Some experienced fishermen prefer to get rid of floats and follow the movement of the line, but this requires many years of training and not everyone can master this style;
• mugs or otherwise called zherlitsy;
• fishing rods are the main component, and with proper skill you can make your own fishing rod. They also have many varieties;
• equipment - various additions to the fishing rod that simplify fishing and change it to suit the needs of the environment;
• nods - help to more accurately recognize the catch;
• homemade boats - their creation requires experience in woodworking and carpentry, but they can also be made from polymers.

With rare exceptions, almost all fishing homemade products fall under this type, and if you miss fishing rods and boats that are difficult to implement, then you can make most of the other gear yourself.

A very common and indispensable equipment when hunting predatory fish:

1. Thanks to vibrations due to the flow of the river or the movement of the fishing rod, it allows you to imitate fish or other small animals.

2. Easy to manufacture and use.

It is most convenient to use them in conjunction with a spinning rod, and these are the simplest fishing homemade products that anyone can do. In order to make homemade spinners, it is enough to make “petals”, which are cut out of metal according to pre-marked templates. After that, several holes are drilled in such a part, and it itself is bent at a right angle so that the first and second holes are on the same straight line. Next, this entire structure is secured to the main fishing line in a simple way.
You can experiment with templates from the Internet or create your own, but to make the work easier, it is better to use ductile metals that are not subject to rapid oxidation.

Float

It is impossible to imagine modern fishing without a float; it has become a kind of symbol of fishing and is displayed on signs in specialized stores.

Most beginners think that this gear has a couple of trivial functions:

• hook support at a given depth;
• bite signal.

In reality, everything is completely different, and, depending on modifications, this simple equipment can perform dozens of different functions. If we talk about the design, then it is a simple “stick” attached to a fishing line, the lower part of which is in the water, and the upper part is above it and should record the movements of the hook. This base can be supplemented in a variety of ways, as evidenced by the many varieties of floats, and each fits its own individual situation, performing specific tasks.

Creating a float at home is accessible to anyone, because it main characteristic- density lower than that of water. Therefore, for the base, you can use any container with air that will allow the homemade product to float, so that it does not turn over from side to side, you need to install a keel or weighting on one side, so to speak in simple language. Attach a signal antenna on top, which should be drawn out in advance. Next, all that remains is to find a metal ring or rubber band that will allow you to attach it all to the fishing line and your homemade float is ready!

Just give our craftsmen from the people a reason to make something. A special article is fishing tricks and homemade products. Firstly, they performed (and sometimes continue to perform) purely practical functions in an era of total shortage of fishing goods. Now you have wobblers, twisters, bloodworms, and telescopic fishing rods - all sorts of good things in bulk (though not always High Quality, but with serious companies you will go broke). But I remember there was a time when even a standing hook or a Klin fishing line - during the day with fire. So the fishing people did their best. And I must say, he did it quite well and with high quality, and most importantly, functionally.

Attempt at classification

All fishing tricks and homemade products can probably be divided into several large categories in the context of their practical application. Firstly, these are all kinds of gear, either copying (with invariable success) foreign fabulous analogues, or real inventions, which, in turn, were copied without a twinge of conscience by Western manufacturing companies (since, naturally, none of the fishermen received a patent ). This broad group includes hooks, floats, spoons, leashes, jigs, donks and much more. Secondly, fishing tricks and homemade products are proven by experience and even invented methods and methods of fishing, feeding, types of attachments and baits. This all relates to the big topic: how exactly to fish in different places and at different times of the year.

Accessories

The third large group includes fishing accessories, invented or copied from existing samples. These are all sorts of devices for longer storage of fish during summer fishing, winter subtleties in terms of equipment on ice, used to avoid freezing, containers for storing bloodworms and other baits. All of them, with rare exceptions, are a real storehouse of folk wisdom, a book of fishing luck. So, for your attention - a small hit parade of homemade products, made from what the fishermen themselves came across.

Toothbrush poppers

Fishing tricks and homemade products sometimes amaze you with a play of imagination. Since newfangled imported things are quite expensive, it clearly makes logical sense to make them yourself. Poppers or walkers are surface baits and should not sink. A little submersion is allowed, but still, the material should float quite well on the water. Therefore, first you need to check toothbrushes for buoyancy. This can be done by collecting water in an ordinary bucket and throwing a brush into it. If it doesn’t sink, but floats on the surface, then that’s it. We carry out the work with a small grinder, reminiscent of a micro-grinder, with removable attachments. We saw off the part with the bristles. We process the edge with a sandpaper attachment. In the lower and upper parts it is necessary to make a hole for attaching the lower tee (attached using a ring with a swivel). We tint the homemade bait (in this case, you can choose red and green - bright colors). We insert the tees. A test in a water bath shows that the weight of the tees is sufficient to sink the structure. To prevent this from happening, glue a narrow strip cut from foam onto the top of the nozzle with superglue. Now the popper does not sink and floats well on the water.

Wobblers

If we are making a wobbler, then we also cut in an additional blade in front of the structure (it can be made from a plastic bottle cap by cutting out a small part). You can paint it with bright nail polish borrowed from your wife. You can also insert an additional weight for weighting. But in our case, the design turned out to be of quite the required weight, and flies far when casting. This is how simple toothbrushes can serve as the starting material for spinning baits.

Spinner for pike perch from broken tweezers

Fishing crafts are sometimes made from anything. But even from broken tweezers. The tool is of high quality (it was once), made of good stainless steel. Why not use a spinner for pike perch? As you know, these predators have a rather narrow throat, and you don’t need a wide spoon either - it’ll do just fine! So, from one leg of the tweezers we cut the workpiece to the required length. We sand it a little, giving it shape and getting rid of small burrs. Now we drill holes where the tee and fishing line will be connected using rings and swivels. This procedure is not so easy to carry out: you can even break a thin drill, since the material is quite durable. Well, it's done. We screw on the tee (preferably on the heavier side, so the spoon will stay more stable in the water column). For aesthetes: you can cut the scales with the same grinder (they already have transverse layers from the tweezers) - just make a couple of even cuts along the length, and the scaly, shiny lure for pike perch or pike perch is ready for use. Such homemade products for fishermen are practically no different from the notorious branded ones. This one turned out even better: the analogue has a tee on the less heavy side, which leads to overlaps and overturning of the spoon.

Fishing trifles in summer

Homemade products for fishing in the warm season can be very useful for both beginners and experienced fishermen. Summer fishing has its own specifics. Great attention should be paid to preserving the catch, since in the heat the fish can spoil very quickly. And the catch caught in the morning, without proper preservation (and in field conditions It’s rare that anyone has a freezer box (except perhaps some car enthusiasts) and may simply not survive until the evening.

How to save what you catch

1. After fishing and pulling the fish ashore, carefully, without squeezing the insides, release it from the hook (otherwise it will quickly fade). You should also not throw severely injured fish into a bucket with the rest of the caught ones - it can ruin the entire catch in a few hours in the heat. Wounded prey is best killed, gills removed and gutted. Next, wrap it in fresh grass ( the best option- nettle) and store in the shade, preferably where there is coolness and breeze.
2. Gutted and gill-free fish can also be salted before storing.

Live storage

If you intend to bring home live prey, you need to store it in water, in a cage or on a kukan (a kukan is well suited for underwater sea hunting, for example). And the cage should have fairly wide rings, the mesh should be made of fabric, not metal. The fish will be seriously injured when trying to escape from the metal. You need to hang it, immersing it in water, in the shade. So that the fish can swim calmly and not hit each other. In a cramped cage there is also a high risk of self-poisoning of the catch with metabolic products.

Homemade cage

More about fishing homemade products. A good branded fish tank is quite expensive - not every angler can afford such luxury. But a cage for storing catch in the summer, long and wide enough (and, importantly, foldable) can be made independently. To do this, we will need strong steel wire or ready-made rings made from it. If you need a compact device, take three rings of descending sizes. Medium is in the middle, small is at the top. You will also need a nylon mesh (the kind that was used for windows against mosquitoes before the widespread installation of metal-plastic ones). We sew a sock from the mesh according to the size of the rings. We put it on and sew it tightly to the rings with stitches. We make sure that the cage is uniform and neat. To prevent the fish from jumping out of the cage, you also need a lid. It can be made from another ring of wire with a mesh stretched over it. Little tricks for the fisherman: our homemade fishnet is attached using a strong nylon rope, which must be tied in a knot to the structure so that it does not float away with the catch, for example. And to prevent your homemade fish tank from flooding if you fish at great depths, you can put a children’s life ring on top of it, as in the photo. Please note that the cage is easy to fold and transport when moving to the fishing spot on foot.

Sensitive float

Let's make fishing tackle with our own hands. Of course, in a store or on the market there is a great variety of floats of different colors and sizes. But choosing a good one is worth it good money. And if you are a fan of fishing with float rods, you need to purchase a dozen floats. And many fishermen prefer to make floats with their own hands the old fashioned way. These tackles are made very well from goose feathers. Where there is a lake or pond or river, these birds are sure to graze. And sometimes they lose their feathers. So all that remains is to bend down and pick it up. You can make large floats and small ones (depending on the size of the feather). We cut off everything unnecessary, leaving only the base of the pen. The result is such a thin stick, light and quite durable. We measure the size of the product. We cut off the unnecessary from the top side (from below, in the place where the feather was attached to the bird’s skin, the structure should have its original appearance, the opposite will lead to the float getting wet). It is convenient to carry out the work with a sharp stationery knife. In principle, the main part is completed. We paint the float in bright colors so that it can be seen on the water. The easiest way to do this is with nail polish, which comes in a variety of fairly bright colors. In addition, the varnish is waterproof. We attach a mount to the cut part of the float where the fishing line will be threaded. You can go fishing. But before that, here are two or three more little tricks for successful fishing.

How to balance a float at home

Often, upon arrival at the float rods, poor balancing of the floats interferes (they are carried away by the current or they lie down without visible reasons). But on the spot, especially in rainy or windy weather, you don’t want to do this, but you have to. Therefore, most correct solution- balance the floats in advance, at home. This can be done by taking a full bath of water and uncovering your gear. So, we tie the float to the fishing line (or attach it to a mount) and begin the process of selecting sinkers. The float should not lift the sinker from the bottom. But the load should not be too heavy, as small bites will not be visible. We find experimentally the golden mean (a lead weight that is too heavy can be cut well with metal scissors, and if it is too small, add another piece of lead). The float in the bathroom should stand clearly, almost vertically, without lifting the sinker from the bottom, but also without lying on its side. Now your fishing crafts are well balanced and you won’t have to do this outdoors. This is especially important in adverse weather conditions.

Fishing crafts: tube for storing floats

For removable floats - one of the most important parts of the tackle. However, some of them are quite fragile and can break when the fisherman moves from place to place. To prevent this from happening, we will make a tube for storing floats with our own hands. We take the base from Tuba, which is very durable. Even if you accidentally step on it, it will not break like plastic, and your floats will be intact. You also need a piece of loose foam about 2 cm thick. Two plugs need to be cut out of it. We make an imprint of the film reel on the foam and cut it out with a stationery knife. One plug should fit very tightly into the hole in the tube. To do this, you can glue it, or use the second one - it acts as a lid. We use a stuck paperclip as a handle for easy removal. The floats are attached from the inside with keels to the foam, securing them well. And the lid closes on the other side. And in order to prevent the cardboard from getting wet, for example, in the rain, you need to additionally wrap the structure around the circumference with tape.

Fishing crafts - a treasure trove of fishing experience

Many generations of amateur fishermen pass on their secrets to each other. And today, despite the abundance of products offered for fishing, someone still needs these fishing tricks. Of course, no one can know everything about fishing. But the above and other tips, we hope, will be useful to both beginners and more experienced fishermen. Happy fishing everyone!