Samsung washing machine diagram. Installation and repair of Samsung washing machines Operating principle of Samsung p 1043

At one time, the Samsung company very quickly entered the world stage and has since become one of the largest and most popular manufacturers in the world. household appliances and some other products. And all Samsung washing units fully meet the manufacturer’s quality standards. The main motto that the entire model range carries is maximum convenience and ease of operation. Yes, it’s true that using Samsung washing units is very simple, but it cannot be said that do-it-yourself repair DIY samsung p1043 washing machine in case of breakdown, it does not cause any special problems. After all, this model has the entire set of programs and modes, without which it is impossible to imagine a modern high-quality washing machine - this is a complex standard programs washing and a few special programs washing, protection against leaks and water overflows and much, much more.

The reliability of this product is from famous manufacturer also top notch. Washing machines of this model can break down extremely rarely, even if the rules for their operation are not followed by the owners very conscientiously. However, over a long period of operation, especially when preventive diagnostics of equipment are not carried out, breakdowns become inevitable. The instruction manual that comes with these machines describes situations where some of the repair work can be done yourself. However, in most cases it is still recommended to contact a specialized service.

The most common type of breakdown that can occur in Samsung machines is a violation of the water draining process, and fault code E2 is displayed. What does this breakdown mean? First of all, the waste water is not drained from the machine. The reasons for this may be a kinked drain hose, a clogged drain filter or a non-functional drain pump. If the cause of the machine malfunction is not the hose, then most likely you will have to seek help from specialized service centers. Our company carries out repair work on all brands of washing machines, including models from Samsung. And if there is no water draining in the car precisely because of a malfunction of the drain pump, then replacement this mechanism in the samsung p1043 washing machine or in will be done in a short time. Because drain pumps are for everything model range Samsung are available in our warehouse.

Our company carries out the entire range, even if they are related to water heating - error code E5, when it is necessary to replace the heating element. And at the same time, you should not be afraid that the repair will drag on for several months, since restoration work requires only branded spare parts. We have all the necessary components and mechanisms that can be immediately installed in the car. The high professionalism of our employees and the availability of modern high-quality equipment will not give any client a reason to doubt the quality of our service.

Pavel (Minsk)

Hello. Washing machine SAMSUNG P1043. Problems:
1.When washing, the time increases (two, three times)
2. The spin may not turn on.

Moscow-Master

Hello! Are you looking at something with heating (the heater heats) or draining (the water drains normally)?
Better yet, call a specialist.

Ilya (Saint Petersburg)

They loaded the machine with more than it could handle.
It gave an error SE (5E), left the water and closed, did not want to drain the water with this load

1. the machine was turned off and the water was drained through the filter
2. took out the laundry, started the rinse + spin mode, put it in an empty machine, filled it with water, drained the water, but again it gave the same error, we are afraid to use it, what should we do?

Moscow-Master

Hello! What brand do you have and what model do you need? There may be 3-5 reasons for the error. For an accurate diagnosis, it is better to call a specialist.

User (Kurgan)

The P1043 machine does not draw water into the tank, but pushes it directly through the drain hose into the sewer, although the drain hose is raised to the proper height. The fault I have with the control module is that it does not turn off the drain pump. Tell me, maybe I'm wrong and this is not a module?

Moscow-Master

The noise of the pump being turned on is heard quite well. If the water is drained and the pump is turned off, then you need to reconnect the machine according to the instructions so that the water does not drain on its own.

Ignat (Chelyabinsk)

The Samsung P 1043 washing machine does not draw water. I checked the external factors and everything is in order with the water pressure. How to look inside now?

Moscow-Master

The two most popular options are a faulty level sensor and fill valve. The water level sensor is located in the tank and its main problem can be called clogging of the tube. The valve is checked by supplying 220 volts. If it opens, then everything is fine.

Vania (Kamensk-Shakhtinsky)

The Samsung P 1043 washing machine began to shake. A check showed that one of the shock absorbers was faulty. I started looking for a replacement and found several different options. I can’t figure out which one I should buy?

Moscow-Master

It should be said that the shock absorbers must be changed as a set. Only then can we talk about the reliability and effectiveness of the work. It is recommended to mount the originals and this is DC66-00421A_ORIG. Replacements recommended by the manufacturer may be used: 12ph20, DC66-00320A, DC66-00343G, DC66-60149A, DC66-00334A, DC66-00343F, 030340.

Anastasia (Arkhangelsk)

The Samsung P 1043 washing machine displays error 8E. What should be done in such a situation?

Moscow-Master

There are several possible failure options:
Device tachometer malfunction. You need to check it - from connection to contact integrity.
The control circuits from the engine and tacho to the SMA module are checked.
All motor contacts are inspected.

Andrey (Perm)

A selection of service instructions, manuals and diagrams for Samsung washing machines and dishwashers. With this documentation you can easily and simply find a common language with your machine.

Service instructions for Samsung F611GW1 F611GW1U F813JGB F813JGE F813JGP F813JGS F813JGW F813JGB F813JGE F813JGP F813JGS F813JGW F1015JGW F1015JGS F1015JGB F1015JGP F1215JGW
Service manual Samsung H1245AGS
Samsung P1091, P1291, P6091, P8091
R1043GW, R833GW1, R843GW Samsung S621GWL, S621GWS, S821GWL, S821GWS, S821GWL2, S803JGB, S803JGE, S803JGP, S803JGS, S832GWS, Samsung S852 (analogue s1052 R1052 R852, MP KS88C4632 memory KS24C010), Samsung SWV-100 0F, SWV-1100F, SWV-1200F, SWV-800F
Samsung WF-R1061, WF-R861

Samsung B813J, B815J, B913J, B915J, B1013J, B1015J, B1045A, B1115J, B1113J, B1213J, B1215J, B1245AV, B1313J, B1315J, B1413J, B1415J, B1445AV, B1513J, B 1515J
Samsung F611 F813J, F815J, F843, F1013J, F1015J, F1043, F1045A, F1213J, F1215J, F1245AV
Samsung P803J, P805J, P843, P1003J, P1005J, P1043, P1203J, P1405J, P1403J, P1205J
Samsung R813J, R815J, R843, R852, R1013J, R1015J, R1043, R1045A, R1052, R1213J, R1215J, R1245AV

Samsung S601, S632, S801, S803J, S805J, S813J, S815J, S621, S821, S832, S843, S852, S1001, S1003J, S1005J, S1015J, S1013J, S1021, S1032, S1043, S1052
Samsung WD8122CVD, WD8122CVB, WD8122CVW, WD8122CVC
Samsung WF J145AC, WF J125AC, WF J105AV, WF B145AC
Samsung WF B125AC, WF B105AV, WF B85A, WF R125AC
Samsung WF R105AV, WF R85A, WF F125AC, WF F105AV, WF F85A

Error E1 (4E) in Samsung washing machines, this may occur when filling water if the machine cannot reach the programmed level within 20 minutes. The defect may be due to low water pressure in the tap, the filter may be clogged, or problems in the water intake valve, level sensor, or electronic module.
E2 (5E)- the drain does not work or is clogged, The drain pump, level sensor, or electronic module may be damaged.
E3 (OE)- activation of the “overflow” relay of the level sensor. It is necessary to check the drain pump level sensor, water intake valve, electronic module
E4 (UE)- no drum balancing. The laundry in the drum is missing or unevenly distributed, you need to make sure that the electric motor drive and electronic module are working properly.
E5 (HE1), E6 (HE2), E8 (CE)- the water heating unit is faulty. Ring the temperature sensor, then the heating element
E7- the water level sensor is not working. Check and, if necessary, replace the water level sensor. They also check the tightness of the tube that goes from the sensor to the tank.
E9 (LE)- water leak or drain connected incorrectly. The water leakage sensor is faulty, check that the drain hose is connected correctly(no self-draining)
DE, DOOR- the door is open if the door is actually closed problems in the electronic module. You can try to turn it off and then turn it on again after 30 seconds if editing the firmware doesn’t help.
tE, EU The signal from the thermistor (heater sensor) is less than 0.2V or higher than 4.5V (thermistor open or shorted Replacing the heating element sensor
3E, EA If after starting the engine in 2 seconds less than 2 pulses are received from the tachometer ( breakage of the motor windings or tachometer) Replacement of tachometer, engine
BE, EV If during the washing mode more than 300 signals per second are received from the tachometer (thyristor short circuit) Replace the control module, tachometer, engine

Solving the problem of spinning in a Samsung R1043 washing machine with a belt drive

Usually, if they act according to the standard algorithm, but in this case, even replacing the pump on the Samsung s821 did not lead to anything. Having measured the voltage at the pump terminals with a multimeter, I realized that it had dropped significantly. Having removed the control module, I saw a charred M2LZ47 triac and a resistor in its control circuit with a resistance of 620 ohms. I tried to ring the KID65003AP microcircuit, or rather the output going to control this triac did not ring. I had to change all this, only I took a chip similar to ULN2003a. After this the pump started working

We repair it ourselves

Using the example of models P1405j, P1205j, P1005j, P805j, which differ only in maximum spin speed and front panel design.

The electric motor in these models is of a commutator type and has built-in overheating protection, and if the winding temperature rises to 150 degrees, the motor will automatically turn off. Since the stator and rotor windings are connected in series, to change the speed of rotation of the motor, it is necessary to change the duration of the power pulses that come from the electronic module.

Motor reversal occurs when the polarity of the stator winding is switched. The Samsung P1405J ED uses 2 stator windings in which smooth adjustment is carried out.

In the diagram in the service manual, the engine is designated as WASHING MOTOR. You can check the washing machine motor by connecting the stator and rotor windings in series and powering the circuit through the LATR.

The following markings are accepted on English-language diagrams:

PUMP MOTOR - drain pump
DOOR LOCK - door lock
THERMISTOR - water temperature sensor, installed on the heating element
Water Sensor - level sensor
NOISE Filter - noise suppression filter.
The entire operation of the washing machine is controlled by an electronic module (PCB CONTROL)

Founded in 1938 in the Korean city of Daegu, Samsung began by exporting food products to Manchuria and China, then moved into food production, and after the end of the war on the Korean Peninsula, its scope of activity continued to expand continuously, covering new high-tech industries.

In 1969, Samsung Electronics Corporation was formed as a result of a merger with Sanyo Electric.

By the end of 1973, the construction of the company's plant for the production of household appliances was completed, and in 1974 the production of refrigerators and washing machines began (model SEW-200W).

In 1993, the corporation's export volume (for the first time among Korean firms) exceeded $10 billion.

Samsung washing machines produced today use modern technologies, such as electronic system Fuzzy Logic control (Sensor Quiet and Sensor Quick series), thanks to which electricity consumption is reduced to 1.6 kWh, water consumption to 45 liters, washing duration is reduced to 95 minutes (all data refers to washing cotton at 95°C).

The original Can Balance balancing system, used in washing machines of the Sensor Quiet series (model SWF 1200), allows you to effectively eliminate load imbalance in the drum. Balls located in front and back parts drum, move in the direction opposite to where the imbalance occurs, compensating for the uneven distribution of laundry (Fig. 1).

Rice. 1.

The noise level during operation of washing machines of this series is 53.4 dB, the vibration amplitude is about 0.3 mm (for conventional machines it is about 1.9 mm). New system balancing replaced traditional counterweights. The “triple waterfall” system used in Samsung washing machines consists of irrigating laundry with jets of water flowing from three ribs on the inner surface of the drum. Washing machine tanks are made of plastic, and although the company has not registered a special name for it, the quality of this substance is not inferior to the quality of materials used by Western European manufacturers.

The company's original development is the multifunctional Jod Dial rotary switch, which allows the user to effortlessly switch to the desired washing program.

Specifications some washing Samsung machines are given in table. 1.

Table 1. Technical characteristics of some Samsung washing machines

	P 6091	SWV-800F P8091	SWV-1000F P1091	SWV-1100F	SWV-1200F P1291
Dimensions (HxWxD), cm	84x60x55	84x60x55	84x60x55	84x60x55	84x60x55
Weight, kg	75	75	75	75	75
Maximum drum rotation speed during spinning, rpm	600	800	1000	1100	1200
Water consumption, l (standard wash program)	54	54	54	54	5	5	5	5	5
Washing wool	√	√	√	√	√
Accelerated wash	√	√	√	√	√
Economical wash	√	√	√	√	√
Cancel spin	√	√	√	√	√
Anti-crease function	√	√	√	√	√
Operating mode indicator	√	√	√	√	√
Remaining time indicator		√	√	√	√
Start delay			up to 24 hours	up to 24 hours	up to 24 hours
Water pressure in the supply line	50...800	50...800	50...800	50...800	50...800
Power consumption, W − washing − wash+heat − spin − drain	180 2000 380 34	180 2000 380 34	180 2000 380 34	180 2000 380 34	180 2000 380 34
Energy class	A	A	A	A	A
Washing quality class	IN	IN	IN	IN	IN
Spin quality class	E	D	C	B	B

Let's meet washing machines Samsung with front loading using the example of Sensor Quick series products. Their general appearance is shown in Fig. 2 and 3. The machines are built according to a classic design and are easily recognizable by the characteristic “corner” in the upper right part of the loading hatch door.

Rice. 2.

Rice. 3. Washing machines Samsung series Sensor Quick(back view):

Control Panel

In Fig. Figure 4 shows a view of the control panels of Samsung washing machines of the Sensor Quick series.

Rice. 4

The elements of these panels have the following purposes:

1. Detergent dispenser hopper.
2. Indicator field. It contains a digital display (in some models), as well as indicators of the selected operating modes of the machine. The digital display shows the remaining washing time, fault messages, etc.
3. Temperature selection button (“Temp.”). By pressing it successively, washing modes are selected in cold water, at 30°C, 40°C, 60°C and 95°C.
4. Button for selecting the drum rotation speed during spinning (“Spin speed”). By pressing it successively, the spin modes are selected:
   Models SWV-1200F/P1291: No Spin, Stop Before Spin, 400 rpm, 600 rpm, 800 rpm, 1000 rpm and 1200 rpm.
   Model SWV-1100F: No Spin, Stop Before Spin, 400 rpm, 600 rpm, 800 rpm, 1000 rpm and 1100 rpm.
   Models SWV-1000F/P1091: No Spin, Stop Before Spin, 400 rpm, 600 rpm, 800 rpm and 1000 rpm.
5. “Delay Start” button (in some models). By pressing it successively in 1 hour increments, the delay time for the start of machine operation is entered (from 1 to 24 hours).
6. “Course” button. Serves to select a washing program (“Cotton”, “Wool”, “Delicates”, etc.).
7. Button “Manual program setting” (“Manual”). When it is pressed sequentially, the following combinations of machine operating processes go through:
   (Wash + Rinse + Spin) - (Prewash + Wash + Spin) - (Spin) - (Rinse once + Spin) - (Rinse twice + Spin) - (Rinse three times + Spin).
   Model P6091:
   (Wash + Rinse + Spin) - (Prewash + Wash + Spin) - (Spin) - (Rinse three times + Spin).
   The pre-wash mode is only used for washing cotton, synthetic and delicate fabrics.
8. Start/Pause button. Serves to stop and restart the machine.
9. Hatch door opening button (“Door Open”, on some models). Used to open the car hatch door.
10. “ON/OFF” button (“On/Off”). The first press turns on the machine, the second press turns it off. If after turning on the machine no button is pressed for 10 minutes, automatic shutdown cars.
11. “No Spin” button (in some models). Enters the spin cancel program.
12. Button “Stop before spinning” (“Spin Hold”, in some models). Enters a program to stop the machine with water in the tank before spinning.

Fault messages

If a malfunction occurs, the sound signal, and the display shows a fault code flashing at intervals of 0.5 seconds. The machine’s electric motor and any other electric drive elements are switched off until the malfunction is eliminated.

1. Water supply system malfunction(message E1).
   The message appears if, when filling water, the change in the carrier frequency of the water level sensor does not exceed 50 Hz or if set level water is not reached for at least 20 minutes. To reset the message, turn off the machine using the ON/OFF button and turn it on again.
2. Malfunction of the water drainage system (E2).
   The message appears if, at the beginning of the laundry load imbalance detection cycle in the drum, the carrier frequency is less than or equal to 25.3 kHz. To reset the message, turn off the machine using the ON/OFF button and turn it on again.
3. Overflow (EZ).
   The message appears when the water level in the tank is too high, which corresponds to a carrier frequency value of the level sensor of 22.4 kHz or higher. Reset is performed using the CL button. If the carrier frequency exceeds 25.24 kHz, the water is forced to drain for 2 minutes.
4. Hatch door open (dE).
   To cancel the message, close the hatch door.
5. Imbalance of laundry in the drum (E4).
   To reset the message, turn off the machine using the ON/OFF button and turn it on again.
6. Heating element malfunction (E5 and E6).
   The message appears when, after turning on the heating element, the water temperature changes by more than 40°C within 5 minutes, or changes by less than 2°C within 10 minutes. Reset is performed using the ON/OFF button.
7. Malfunction of the level relay (E7).
   Abnormal values ​​of the carrier frequency of the level sensor are considered to be values ​​of 30.00 kHz ( top level water fill) and 15.00 kHz (lower level). A malfunction is considered when one of these frequency values ​​persists for 5 seconds or longer. When this malfunction occurs, the drain is turned on for 3 minutes, after which the drain pump is turned off and a fault message appears on the display.
8. Abnormal temperature values ​​(E8).
   Values ​​considered abnormal are 60°C or more for synthetic fabrics, 45°C or more for delicate fabrics, 45°C or more for wool. If, when pouring water into the tank, the water temperature is abnormal, force the water to drain for 2 minutes (as if it was overflowing).

The troubleshooting algorithm is given in table. 2

Table 2 Troubleshooting algorithm

№	Malfunction	Corrective Action
1	No mains power	Check the presence of voltage in the network and the serviceability of the power cord. Check the contacts of the control board, noise filter, fuse, and the voltage at the output of the power transformer.
2	There is no water coming into the car	Check whether the tap on the water supply line was opened and whether the “Start/Pause” button was pressed after selecting the washing program. Check the EC contacts, the integrity of its coil, and the level relay contacts. If all these parameters are normal, replace the control board.
3	The water fill is completed, but the wash does not start.	Check the contacts and serviceability of the level switch, the presence of kinks in the tube going to it, and its tightness. Check the operation of the level relay. If all these parameters are normal, replace the control board.
4	The water filling has not yet finished, but the washing has already begun.	The control board is faulty. Replace the control board.
5	The drum does not rotate during washing.	Check that the drive belt is installed correctly. Check the integrity of the rotor, stator and tachogenerator windings of the electric motor, as well as the fuse.
6	When washing, the drum rotates in only one direction.	The control board is faulty. Replace the control board.
7	Bad drain.	Check for kinks in the drain hose, the integrity of the drain pump winding, and clean the drain pump filter. If all these parameters are normal, replace the control board.
8	Bad spin.	Imbalance of laundry in the drum. They redistribute the laundry and start the machine again.
9	Increased noise during spinning.	Check the tension of the drive belt. Check that the shipping fasteners have been removed. Make sure the machine is installed on a level and stable floor.
10	The residual current device is tripped. When washing, the machine on the panel knocks out	Check the grounding of the washing machine. Overload during simultaneous operation of the washing machine and other electrical appliances. Wash in cold water (without using the heating element).
11	No water heating.	Check the contacts of the heating element and measure its resistance (normally 20.5...21.5 Ohms) If all these parameters are normal, replace the control board.

Attention: the control board of the washing machine is filled with polyurethane, so its individual components cannot be replaced, and the board circuits cannot be checked with a tester probe. When replacing the board, be careful not to damage the protective coating. Before performing operations on the board, it is necessary to remove static electricity.

Test mode

To login test mode(Fig. 5):

Rice. 5 Entering the test mode of the washing machine

1. While simultaneously holding down the " 1 " And " 2 ", press the "ON/OFF" button.
   A message appears on the display ( tE).
2. After pressing the button 3 » testing of the motor group of the washing machine begins.

Sequence of stages of motor group testing:

Opening the EC for pre-wash (0.3 sec) - OFF (0.3 sec) - Main wash (0.3 sec) - OFF (0.3 sec) - Opening the EC for rinsing (0.3 sec) - OFF ( 0.3 sec) - Turn on the drain pump (0.3 sec) - OFF (0.3 sec) - Turn on the relay 1 electric motor (0.3 sec) - OFF (0.3 sec) - Turn on the relay 2 electric motor (0, 3 sec) - OFF (0.3 sec) - Turn on relay 2 of the electric motor (0.3 sec) - OFF (0.3 sec) - Turn on the heating element relay (0.3 sec) - OFF (0.3 sec) - Opening hatch door (this mode lasts as long as the door remains closed).

Electric drive

In Fig. Figure 6 shows the principle of rotor rotation reversal and the electric motor switching diagram,

Rice. 6

and in Fig. 7 - geometric parameter H of the electric motor (thickness of the plate pack).

Rice. 7.

The value of the parameter H and the resistance of the stator and rotor windings depend on the type of electric motor used in a particular machine. These values ​​are given in table. 3.

Table 3. Parameters of two types of electric motors

In Fig. Figure 8 shows the hatch locking device. The nominal resistance of the solenoid winding is 210 Ohm±10%.

Rice. 8. Hatch locking device

The heating element of a 2000 W washing machine has a nominal resistance of 23-29 Ohms and is equipped with a protective fuse at 128°C.

Disassembling and assembling the washing machine

Top cover (Fig. 9).

Rice. 9

• Unscrew the two mounting screws on the back of the machine.;
• Move the cover back 15 mm and lift it.
• Access to the transformer, level relay and noise filter is provided.

Front panel (Fig. 10 and 11).

Rice. 10

• Remove the top cover and the detergent dispenser hopper.
• Unscrew the two screws securing the control panel on the front and one screw on the right.
• Use a screwdriver to separate the front panel on the left side.
• By pulling out the lever, separate the plinth panel (except for model P 6091).

Rice. eleven.

• Remove the fastening clamp and the hatch seal.
• Remove the eight screws securing the front panel.

Access to the heating element, drain pump, shock absorbers and hatch door lock is provided.

Drive belt (Fig. 12).

• Remove the top cover.
• Remove the belt from the pulley.
• When reassembling, first put the belt on drive pulley 1, then on driven pulley 2, placing the belt in the center of the pulley.

Rice. 12.

Electric motor (Fig. 13).

With the car on its left side, disconnect the wiring harness from the electric motor.

Rice. 13

Unscrew the fixing bolt through the mounting hole and remove the electric motor.

The structure of Samsung washing machines is shown in Fig. 16-20, lists of relevant components are given in table. 4-8.

Rice. 16 Samsung washing machine structure (tank and drum)

Table 4. Samsung washing machine components (tub and drum)

Pos.	Code	Qty	Description	Notes
1	DC47-00001A	1	heating element	2000 W
2	DC61-30346A	1	Front of tank
3	DC61-40348V	5	Bracket
4	DC61-40344A	1	Heating element mounting bracket
5	DC61-60496A	2	Heating element spacer
6	DC60-20061С	3	Screw
7	DC62-20311A	1	Overlay
8	DC60-60188A	1	Washer
9	DC60-20061С	1	Screw
10	DC91-12281A	1	Drum
11	DC62-40183A	1	Sealing ring
12	DC97-00214A DC97-00214В	1 1	Rear tank	P1291/P1091 P8091/P6091
13	DC61-60499V	8	Tank clamp
14	DC61-60520A	1	Tank clamp

Rice. 17 Samsung washing machine structure (drive, hatch seal)

Table 5. Samsung washing machine components (drive, door seal)

Pos.	Code	Qty	Description	Notes
1	DC91-12078A	1	Clamp
2	DC61-20219A	1	Hatch seal
3	DC91-12077A	1	Clamp
4	DC60-40138A	2	Bolt
5	DC60-60044V	5	Washer
6	DC60-60040A	3	Washer
7	DC66-60154A	1	Counterweight
8	DC61-60497A	1	Clamp
9	DC62-10305A	1	Pipe branch
10	DC60-40140A	2	Bolt
11	DC60-40132V	1	Bolt
12	DC62-10303A	1	Drainage tube
13	DC66-60153A	1	Counterweight
16	DC62-40184A	1	Pad
17	DC61-10676A	1	Lid
18	DC60-20014A	2	Screw
19	DC61-60497A	1	Clamp
20	DC62-10304A	1	Pipe branch
21	DC65-60118F	1	Ring
22	DC66-10176V	1	Pulley
24	DC60-60049A	1	Washer
25	DC60-50014A	1	screw
26	DC66-10139A	1	Belt
27	DC31-10181A DC31-00002С	1 1	Electric motor	Type A Type B
28	DC61-00041A	2	Sleeve
29	DC60-40138A	1	Bolt

Rice. 18

Table 6. Washing machine components Samsung(casing and electrical components)

Pos.	Code	Qty	Description	Notes
1	DC96-00070A DC96-00070В DC96-00052В	1 1 1	Wiring harness	Р1291/1191/1 091/8091 (Cold + hot) Р1291/1191/1 091/8091 (Cold) P6091 (Cold)
2	DC96-00053A DC96-00053В	1 1	Wiring harness	Р1291/1191/1 091 P8091/P6091
3	DC60-20136A	2	Screw
4	DC61-30344A	1	Support frame
5	DC32-30006Р	1	Level relay
6	DC61-60063V	1	Clamp
7	DC62-10311A	1	A tube
9	DC60-20050С	2	Screw
10	DC60-20054С	1	Screw
11	DC60-30015V	2	Screw
12	DC91-12083A DC97-00218A	1 1	Top cover	"Under the tree" "Under the steel"
13	DC61-30345A DC61-00056A	1 1	Front Panel	P6091
14	DC60-20054С	6	Screw
15	DC60-20030A	1	Screw
16	DC61-00115A DC61-00122A	1 1	Hatch door lock	P6091
17	DC66-30160A	1	Lever arm
18	DC61-70216V	1	Spring
19	DC61-60180A	3	Sleeve
20	DC61-70217V	2	Spring
21	DC62-30313A DC62-30314A	1 1	EC	Hol. Hol. + mountains
22	DC61-60063V	6	Clamp
23	DC62-10068A	1	A tube
24	6001-000947	2	Screw
25	DC29-00002A	1 1	Anti-interference filter
26	DC60-20138A	1	Screw
27	DC96-00146A	1	Power cable
28	DC61-40086A	5	Retainer
30	DC97-00139В	1	Drain hose
32	DC65-60118F	1	Crimping ring
33	DC61-30342С	1	Frame
34	DC91-12292A	4	Leg
35	DC66-60149A	2	Shock absorber
36	DC60-40026A	2	Bolt
37	DC61-10672A	1	Plinth panel
38	DC61-10673A	1	Stub
39	DC62-10302A	1	Drain hose
40	DC90-11110K DC90-00149A	1 1	Drain pump	P1291/P1091 P8091/P6091
41	6002-000444	2	Screw

Rice. 19

Table 7. Samsung washing machine components (access door)

Rice. 20

Table 8. Samsung washing machine components (control panel, detergent dispenser)

Pos.	Code	Qty	Description	Notes
2	DC97-000040	1	Hopper panel
3	DC61-30348A	1	Bunker
4	DC61-60498A	1	Nozzle
5	DC61-10687A	1	Cup
6	DC97-0000ЗМ	1	Control Panel	Р1291/Р 1191/Р10 91
8	6002-000445	2	Screw
13	DC96-00132A DC96-00133A DC96-00134A DC96-00135A DC96-00136A	1 1 1 1 1	Control board	P1291 P1191 P1091 P8091 P6091
14	6002-000554	3	Screw
17	DC91-12084A	1	Distributor cap
18	DC61-10679A	1	Distributor housing

The article was prepared based on materials from the magazine "Repair & Service"

Katya 03/23/17

In our apartment, in the kitchen, there is a built-in Neff dishwasher. And as you understand, dismantling and delivering it to a repair shop would take a lot of time and effort. Therefore, we invited the master of this service center with home renovation. The car served us without interruption for three years, but still, the time came when it required repairs. All the problems were with water quality. It was because of her that the car failed. The technician advised us to install an additional filter, especially for the dishwasher. And in the future there will be no more such problems. I also really liked that before arriving, the repairman asked about the model of the car and what happened to it during the breakdown. This gave him the opportunity to take all the necessary parts with him at once and carry out repairs on the spot. I am very pleased with the repair and the technician who did it.

Anton 03/24/17

We have a very small family, there are only two people in it, and a dishwasher Bosch machine also compact in size. This equipment served us every day for 8 years without any breakdowns or complaints. But there came a time when it simply stopped working. Before going to work, I called the repair shop and agreed that I would bring them a dishwasher for repair. They didn't even ask the model, they just agreed to do everything. I brought it, left it, and said that when it was fixed, they would call me back. After lunch I received a call, the car was fixed and I could come pick it up. After work I did just that. In fact, we only had one day without a dishwasher. Everything was done very quickly.

Georgy 04/19/17

Not long ago I asked for repairs when my wife said that the dryer (which we have is a Miele brand) stopped working, or rather the drum in the machine stopped spinning when you try to start it. There was nothing to do, I began to call the master.
A young man arrived, looked and said that our control unit board was broken, voicing the price of repairs. I expected a much larger amount, so I was glad when I heard a figure that was 2 times less than I expected.
Overall, I’m satisfied, the repair took more than an hour, and the master was very careful in his work, he managed to observe the process, and while communicating on abstract topics, he slowly carried out the repair.

Tatyana 08/15/17

I found your site on the Internet. Washing machine Bosch. After the application, Alexander Leonidovich Baranov arrived the next day. Master of the highest category. Professionally, methodically, and with knowledge of his craft, he fixed all the problems: replacing the heating element, it was leaking, knocking out the RCD. There are many problems. I already went to the repair shop once. The repairman waved his hand at the leak: “it happens,” he replaced the heating element, although it was in working order. In short, there is something to compare with. Therefore, the meticulousness and attention of Alexander Leonidovich surprised and pleased! THANK YOU! I agree with Irina: YOU ARE THE BEST!!!