Router Asus RT-N10 - a simple solution for organization wireless network. This model features a classic design and ease of setup. This process will not be difficult for anyone if they follow the simple instructions.
Appearance and characteristics of the Asus RT-N10 router
The model has a laconic classic design, so it will fit perfectly into any interior. On the front of the case there are indicators that can be used to determine the device’s operating mode, network connection status, and so on. At the back there are USB and LAN ports, as well as a WAN input for the provider cable - everything a modern user needs. An antenna is installed on the housing, providing wireless Internet access in the home.
The model has a classic design
Table: model characteristics
Turning on the router for the first time, automatically obtaining a network address in Windows
When you turn on the device for the first time, you can ensure that the distribution of network addresses necessary for the correct organization of a wireless network is carried out automatically. To do this you need to do the following:
Advanced router settings
The web interface on original and branded (from Rostelecom, Beeline or other providers) Asus-RT N10 routers, as well as most models in this line, is the same. Therefore, these instructions can be used by any owner of the same or similar devices.
Entering settings and changing authorization data
All router settings are available via the web interface. Login and change required parameters can be done as follows:
Setting up an L2TP connection for Beeline
Some necessary parameters, such as user login and password, are specified in the agreement. To configure, do the following:
Setting up a PPPoE connection for Rostelecom and Dom.ru
Do the following:
The router will restart with the new settings. There is no need to enter the host address: in the Rostelecom and Dom.ru networks it will be received automatically.
Setting up a PPTP connection for all providers
PPTP communication on routers of this model is configured in the same way as PPPoE and L2TP:
Setting up a static IP address
Static IP is issued by your provider. To configure it, do the following:
Setting up a Wi-Fi hotspot
Access point mode is the most common when using routers. On Asus RT-N10 it is configured via the web interface. To do this you need to do the following:
Setting up IPTV
This procedure boils down to setting up one of the LAN ports to receive a signal from an IPTV set-top box. To do this, follow these steps:
Setting up a router in repeater mode
Repeater mode is an expansion of the signal reception area. The settings are the same on all Asus models that support it. To configure you should take next steps:
- Go to “Administration” - “Operating mode” and select repeater mode.
Repeater mode allows you to extend the range of your wireless network
- From the found Wi-Fi networks, select the one whose coverage you would like to expand.
Thanks to the repeater mode, you can connect to the Internet where there was no access to it before
- Enter your key Wi-Fi networks this router.
To expand your Wi-Fi network you need to know its password
- Assign a name and key to the Wi-Fi network in repeater mode. You can select the same options as the original ones.
If you wish, you don’t have to change the name and password of the Wi-Fi network at all.
- Wait until connected to the selected network. If the connection is successful, the router will report the newly configured network.
Sometimes connection can take a long time
Resetting the router
To do this, you need to hold down the Reset button located on the back of the device. In addition, you can reset the router settings from the web interface. The procedure is performed by going to the address " Additional settings" - "Administration" and then clicking the "Restore" button. After restarting, the router needs to be configured again.
Recovery initial settings You will need a router if the device stops working correctly
Firmware update
The firmware for the router can be downloaded from the manufacturer’s official website. The update process itself looks like this:
After restart old firmware will be replaced with a more recent version. After the update, you may need to reconfigure some (or all) router settings.
Video: how to set up the Internet on the Asus RT-N10 router
It is difficult to imagine a modern home or office without a connection to the World Wide Web.
Prepared by us detailed instructions ASUS RT N10P router settings will help you connect to the Internet on your own; we will look at how to properly connect the device with cables, enter settings depending on your provider or operating system, set up WiFi.
Turning on the router
This device includes: the router itself, a power adapter, and a cable for connecting to a computer.
This is enough to start connecting and then setting up the device.
Let's perform the following steps in order:
- connect the power adapter to the device and to a 220V socket;
- We insert the Internet cable into LAN 1 on our device, and insert the other end into the computer port (if the provider’s wire was there before, it should be removed);
- We connect the Internet provider cable to the WAN socket on the device;
- turn on by pressing a button.
Photo: Turning on the router by pressing a button
The router begins to download the firmware. A model of the same device with firmware v2 will not differ in settings, the only difference is in the size of the firmware storage memory.
After connecting the device to the mains, it is recommended to full reset settings.
This is done by pressing and holding for 12-15 seconds with some thin object (pen, paper clip) on the back panel of the button in the Reset hole.
Preparing for setup
You need to understand that now your computer has another intermediary on its way to the Internet - your router. He takes on a number of tasks to ensure communication. Next, you need to make sure that the Internet protocol settings on your computer are set to automatically obtain an IP address.
After connecting the computer to the router, network address it will be assigned not by the provider, but by the router itself. It forms its own network and assigns addresses in it. You should also make sure that the computer will automatically receive the DNS server settings - this is a server that interprets the site names you enter into the “language of communication” of the servers.
Photo: Network formation and address setting
Often it is this setting, when the network is in complete order, that influences the fact that the pages on your monitor screen do not come off.
We find in the settings of your operating system:
- connection via local network;
- open Properties;
- Next, go to Internet protocols and note that we will receive the IP address and address server address (DNS) automatically.
How to enter ASUS RT n10p settings
We launch an Internet browser on the computer. In the field for entering Internet addresses, enter four groups of numbers separated by a dot - this is the network address of the device being configured. For this model, the address usually used is 192.168.1.1. There is no period after the last unit.
A field for entering your login and password should appear on the screen. By default, the manufacturer specifies both the login and password - admin. Confirm by entering. If the field for entering your login and password does not open, you can check the address of your device on the product body.
Connection
After we have figured out how to access the router settings via the WEB interface, we can connect to the provider’s server. The settings of different Internet operators may differ, so below we will look at the most common ones.
Setting up for Beeline (Beeline)
We go to any browser, in address bar Enter the network address of the router and find yourself in the Network Map window. Next, in Advanced settings, select Internet.
Specify the parameters:
- WAN connection type - L2TP;
- get an IP address - automatically, Yes;
- connect to DNS - automatically, Yes;
- login (the account number that you pay) and password (the same one that is needed to enter your account on the provider’s website);
- VPN server - tp.internet.beeline.ru;
- We confirm.
Setting up for Rostelecom
Also, as in the previous case, we get into the settings. Next, click WAN.
Enter required functions for connection, the main ones among which will be:
- connection type - pppoe;
- automatic obtaining of an IP address;
- DNS needs to be set, also automatically.
Enter your username and password (you can see them in the contract). If there is no contract, you need to call the provider’s technical support, they will be able to help you recover your data. It is not necessary to change the remaining parameters.
After setting up a connection to the provider’s server, you can start WiFi setup ASUS rt n10p and secure access parameters.
You need to go to Wireless Network and specify the following settings:
- Fill in the SSID column with the name of the network. This name will be broadcast and you will select it to connect to WiFi;
- in the Authentication Method column, indicate the most secure type of protection for the WPA2-Personal network;
- In the pre-shared key field – enter the network password. We indicate it in English letters and numbers; there must be more than eight characters.
How to reset settings
If the router works intermittently and reconfiguring it does not bring results, then reset them and enter the settings again. On the back panel of the device, in a small hole, you need to press the Reset button with a sharp object and hold it for 12-15 seconds. As a result, the power indicators on the device will light up. This means that the settings have been changed to their original settings.
The settings are also reset in the router's control panel. Go to the Additional settings section, click Administration, Manage settings, Factory settings and select - Restore.
How to set a password
In Administration, System, the access data for the device menu is changed. After entering the password, you should remember it or write it down. Remember, the Wi-Fi password and the menu access password are different passwords.
If you forgot WiFi password You can always change it in the device menu, and if you forget the data to access the device menu, you will have to reset the settings to factory settings and configure everything again.
Setting up IPTV
If your provider supports the transmission of television channels over the Internet, you can access them through your router. Let's use the web interface again and open the router settings. We will be interested in additional settings, LAN and route.
We check that multicast routing is enabled (it should be Yes). In the IPTV UDP Multicast to HTTP Proxy Port column, you can enter the value 1234 (this is useful when you need to make your work easier WiFi networks, freeing it from multicast packets). That's it, the channels are configured for wired TV set-top boxes.
To provide access to TV channels to wireless clients, you will need to go to Advanced settings, Wireless network, Professional and set the Multicast routing speed to 24. Please watch TV on a tablet or laptop.
Finally, let’s clean up our wireless network from multicast packets. HTTP packets will be broadcast instead. IN previous settings we have already set the value to 1234. Open the list of channels - this is a file in .m3u format. To do this, we will use any text editor.
Video: Setting up ASUS RT N10P router
Udp://@239.23.0.200:1234/ - this is what the recording of each television channel looks like at the beginning. And we need to change each entry, presenting it in this form: http://192.168.1.1:1234/udp/239.23.0.200:1234/. Eight digits - 192.168.1.1 - is the router address. If your device has a different address, they need to be changed to yours.
1234 is the previously set proxy port (set your values if they differ from those indicated above). We edit the list of channels, save and use it in the player to watch IPTV. Setting up iptv completed.
If you have PPTP
To connect to a PPTP provider, you need to specify network settings, which are issued by the provider. The same as in the case with PPPoE connection, enter your username and password. The PPTP server can use encryption or select the Auto option.
Another required parameter for connection: you must specify the IP address of the provider's PPTP server.
To view the status of the pptp connection, you need to go to the Network Map option.
Updating the firmware
To update the firmware, you need to go to the ASUS page on the Internet and find our device, indicating its model. Then select the type of your operating system and download required file: http://www.asus.com/ru/Networking/RTN10P/HelpDesk_Download/.
After this, in the additional settings you need to open the Administration option and run the firmware update. To do this, select the previously downloaded file through Explorer and click the Send button.
Question answer:
Can the ASUS RT N10P router work with a USB drive?
Answer: no, unlike the ASUS rt n10u model, it is not equipped with a corresponding connector.
Can it work with a 3g modem?
Answer: it cannot, it is not equipped with a USB port.
How to make access point mode?
Answer: The modem settings allow it to be used in several operating modes to meet different requirements. Launching Quick setup Internet, then Internet Settings, you can select Access Point (AP) Mode.
How to connect a printer?
Answer: If the printer is equipped with a WiFi module, it can be connected to your router's wireless network using the WPS button.
This router meets all modern requirements: a convenient menu for setting up the asus rt n10p router, security, a wide range of settings. You can stream up to four networks with different access levels. The device is ready for use, you can access the Internet both via WiFi and a wired connection, print documents without connecting wires to a laptop, and so on.
In this article we will tell you how to configure an asus router. It should be understood that routers from the manufacturer Asus require several modifications, therefore, the setup process may differ slightly. However, as practice shows, there are no significant differences in connecting and configuring Wi-Fi routers asus. Below are the setup instructions Wi-Fi router and Asus RT-N10.
But the guide is perfect for others too. Asus models RT. Also, the process of setting up the network connection itself implies slight differences in the type of connection used by your provider. In this instruction we will consider the option of connecting wireless router to providers Rostelecom and Beeline. If you use the services of another Internet provider, then there is nothing wrong with that; by analogy, you can set up a router for other providers. You can find out the network type on the provider’s official website or by calling the support service. In this article we will only look at setting up the Asus router; as for the connection, the scheme is standard. To help you, the instructions given in the article “to“.
How to log into the web interface of the Asus router?
All necessary settings wifi routers are made in a special web interface, which is a kind of menu. To get to this interface, you need to enter 192.168.1.1 in the address bar of any browser, after which you will see a form in which you need to enter your login and password to access Asus settings. The default login for Asus routers is admin and a similar password.
If you suddenly fail to log in using these data, then look at the documentation of your router, there you can find all necessary information. After entering your login and password correctly, you will find yourself in the Asus router settings web interface.
Setting up an Asus router connection for the Beeline provider
Below we will look at the tincture process Wi-Fi router Asus for Internet provider Beeline. To do this you need to perform the following steps: home page In the router’s web interface, find the “WAN” section and click on it, now specify the connection parameters. We are looking at how to configure an asus router, and therefore the picture below shows a list of parameters for beline l2tp. If you have a different provider, then the data will be different accordingly (you can find them on the official website of your Internet provider).
Now you need to select the type of WAN connection, select L2TP. In the “select IPTV port” item, select a port if you plan to use television from the Beeline provider. In the item “Obtain a WAN IP address automatically”, set “Yes”. We also set the “Connect to the DNS server automatically” item to “Yes”. In the “Username” line we indicate your login to access the Internet. In the “Password” line, indicate your Beeline password accordingly. In the “Heart-Beat or PPTP/L2TP (VPN) Server” field, enter tp.internet.beeline.ru. You don’t have to specify anything in the “Hostname” line. Now all that remains is to click on the “Apply” button for all the settings to take effect.
If you did everything correctly, the Wi-Fi router should already have established a connection to the Internet. All you have to do is configure the wireless network, that is, come up with something for your wi-fi and set a password to connect to your network. You shouldn’t have any problems with this, and if something is still unclear, you can find instructions for setting up a wireless network. This article describes the process of installing a router from another manufacturer, but the meaning is the same. Also brief instructions waiting for you at the end of this article.
How to configure an asus router for the Rostelecom PPPoE provider
If you use the services of the Rostelecom provider, then to configure the Asus router you need to complete the following steps: Go to the “WAN” section and fill in all the connection parameters as indicated below.
- WAN connection type: PPPoE.
- Selecting an IPTV port: indicate the port if Rostelecom IPTV television will be used.
- Obtain an IP address automatically: Yes.
- Connect to DNS server automatically: Yes.
- Username: Your Rostelecom login.
- Password: Your Rostelecom password.
It is not necessary to touch other points. Click “Apply” to save all changes. After this, you should already have Internet access.
Concerning Wi-Fi settings on an Asus router, then, as already indicated, everything is simple here. Select the “Wireless Network” section and fill in the required fields. The wireless network name is specified in the SSID field. The Wi-Fi password is set in the “WPA Pre-Shared Key” field.
So now you know how to set up asus. If you have a different provider, then simply change the data, proceeding by analogy. If you have any questions, leave a comment and we will try to give a detailed answer.
Loading...
