The connection process for the DIR-300 model is not fundamentally different from other home modems from this company. We will tell you in detail how to set up a company router D-Link DIR 300, let’s imagine step by step instructions. To set up your D-Link router, you will definitely need to log into GUI, which will also be discussed in this material.
Connecting the router to the network and to a PC/laptop
After purchasing a router, you need to figure out how to connect it. There is nothing difficult in this procedure, as you will see for yourself. Prepare before you start network cable required length. Next, follow these steps:
The power and corresponding LAN connector indicators on the front panel should light up. Congratulations! The first stage is completed. Then you can move on to the software part.
How to reset all settings
During operation, the router may not work correctly: the Internet will disappear or some parameters will be lost. In most cases, such software errors are corrected by resetting to factory settings. This can be done in two ways: through the web interface (section “System” -> “Configuration”) or hardware. There is a button on the back panel labeled Reset. To reset settings, press and hold it for more than 10 seconds. A successful reset will be indicated by the simultaneous lighting of all lights on the front panel.
Attention! To press, you will need a paper clip or toothpick. Afterwards, the user will have to re-configure the DIR 300 router.
Firmware update
If setting the factory parameters did not give positive result, the next step to restore the router to full functionality is to update the firmware. The device comes with the original version from the factory. On the official website of the TP Link company (via search) you can find latest version firmware and download. The file has bin permission and is located on the website in the Firmware directory. Next, follow the steps of the following instructions:
The process will take a few minutes. After the end will happen automatic reboot. New firmware, as a rule, is more efficient because it eliminates microcode flaws. Roll back to previous version You can use the same method by downloading the necessary software from the site and installing it through this menu.
Login to the web interface
In order for the D-Link router to distribute the Internet to PCs and other devices, it is necessary to make adjustments. The first step is to log into the modem interface. Before you begin, you need to know your username and password to log in. You can find information on the device label. The IP address to which the transition should be made is also indicated. If the inscription is damaged, then try using standard admin for both input fields.
Once you have the required data, run:
Only after this you will be able to change device settings.
Network connection properties
Setting a new password for logging into the web interface
We definitely recommend replacing the standard factory key with a more reliable one. Third-party “pests” can enter the device menu (if Wi-Fi is not protected) to change the name or completely deny your access. The change takes place in a couple of minutes:
Be sure to write down the new key in a notepad or diary so you don’t forget.
Setting up a wired connection
To use the Internet, you must configure the D-Link DIR 300 connection. Log into the interface using the router’s IP address. Check with your provider for your connection type and authorization information. They are usually specified in the contract, a copy of which the subscriber receives when connecting to the Internet. All actions take place only in the “Network” section:
Please note that when connecting, the system will ask for a password and login. You must enter the data provided by the service provider. The network you set up should work without problems, so try accessing any Internet resources.
Wi-Fi connection
As you noticed, the modem has a small antenna. Through it, the Internet is “distributed” over the air, since the DIR-300 is a Wi-Fi router. Creating a wireless access point occurs in the “Wi-Fi” section:
On this Wi-Fi setup finished. Save the changes, and then try to connect to Wi-Fi.
Connecting to a router via Wi-Fi
On your laptop/smartphone or tablet, activate Wi-Fi. In the search for available Wi-Fi, find your SSID name. You must be within signal coverage. Click on the access point and then enter the password you set before. If the procedure is successful, the word “Connected” should appear next to the name of the point.
The next time, the connection to the D-Link DIR 300 router via Wi-Fi will be performed automatically without the need to re-enter the data.
Other settings
For advanced users, the router can provide more advanced settings. They will help you activate VLAN, client mode and much more. Let's talk about how to configure specific functions in DIR 300 in detail.
Setting up routing
In the “Advanced” menu section and the “Routing” subsection, the user can add static routes to the system to networks that are connected directly to the device.
To define a new route, click “Add”. In the line, set the following parameters:
- the destination network to which you plan to create a route;
- destination network mask;
- IP gateway, i.e. the address through which access occurs;
- metric that determines priority;
- field “via interface” (in the drop-down list, select the connection to access).
After the task, click the “Apply” button. This is how the routing table is configured in D-Link.
VLAN
Using VLAN, the user of the D-Link router can create and change groups of ports for virtual networks. First erase entries from the group on the page before creating a group with LAN ports:
- Select the desired group.
- Remove the flag located on the left side of the port. Click "Save".
Creation new group VLAN is performed through the “Add” button. All that remains is to fill out the fields.
Below are some instructions on how to set up your Netgear N300 router with detailed description all stages of action, which are illustrated with explanatory drawings. It should be noted that the procedures for connecting the device and entering parameters into its interface are not difficult, therefore, if you have step-by-step guides even a novice user will be able to independently configure the device taking into account his specific requirements and conditions imposed by Russian communication service providers. The article also outlines a method for flashing the Netgear router version N300 and resetting its parameters to the factory state.
How to connect the device?
Before you begin the procedures for setting up your Netgear router, you must correctly connect it to your computer.
To connect Netgear to a desktop PC or laptop, you will need to complete the following few steps:
Setup Instructions
First you need to make some settings on your computer to implement IP assignment in automatic mode. For this purpose, it is necessary to carry out the following sequential actions (using the example of the most popular Windows 7 today):
For Windows XP, the algorithm of actions is not significantly different from the previous one:
- Click “Start” and launch “Control Panel”;
- Then go to the “Network Connections” section;
- Click “Local Area Connection” and then “Properties”;
- Enter the “General” tab;
- In “Internet Protocol”, check the boxes for assigning “IP” and “DNS” addresses automatically;
- Click “OK”.
How to enter the router settings?
The following steps must be followed:
- Open an Internet browser on your PC and type “192.168.1.1” in the address field;
- In the menu that appears, type the name “admin” and the access code “password” if the device is new and the parameters have not been adjusted previously, otherwise, if you do not have a valid password, you will have to first return the settings to their original state, using the last instructions from this article;
Options for entering parameters in the Netgir interface
There are several connection methods.
Using a dynamic IP address
The algorithm of actions consists of the following sequential stages of action:
If the provider uses a "PPPoE" connection
This type of connection is used by large Russian communication service providers, for example, Dom.ru, TTK and RTK.
The following actions are required:
If using L2TP connection
This type of connection is used by the Beeline company.
You need to do the following:
Wi-fi network setup procedure
The following several steps must be taken:
How to install new software?
In order to flash the device, first, with official resource manufacturer must be downloaded and saved in PC memory current version software and then do some of the following:
How to factory reset your router
The following steps need to be taken:
- There is a special recessed part on the router case (to protect against random clicks) the “Reset” key, which must be pressed using a thin, sharp instrument, for example, a straightened paper clip, and held for ten seconds;
- The light indication should blink;
- Ready! You can now open the interface to enter parameters using the factory name and access code that were specified at the very beginning of this manual.
After this, you need to configure the device, following the above instructions.
The DAP-1320 wireless repeater is portable device, increasing the coverage area existing network. The device can be placed anywhere in your home. Compact and fits in the palm of your hand, the DAP-1320 is powerful and supports wireless speeds of up to 300 Mbps.
Easy setup and use
There are several simple ways settings of the wireless repeater DAP-1320. You can use the QRS Mobile application, supported by iOS or Android mobile devices. You can also perform setup with one click of the WPS button on the DAP-1320 repeater and on the router or access point whose coverage area you want to increase. In addition, you can simply plug the DAP-1320 into an electrical outlet, connect to the device wirelessly from a computer, or mobile device and follow the installation wizard steps.
Compact and easy to install design
The compact size allows you to install the repeater at home or in a small office; the device does not take up much space and is ready for use immediately after connection. The wireless repeater plugs directly into an electrical outlet, so there is no need for additional cables or bulky power supplies. Thanks to its neat and compact design, the DAP-1320 fits perfectly into any interior.
The instructions will show you the basic characteristics and help you set up the D-Link DIR-300 router, correct setting even such a budget router will help organize a full-fledged home local network, and when purchasing a more powerful router, the D-Link DIR-300 will expand the infrastructure, becoming an excellent addition to the new device.
Before setting up the D-Link DIR-300, you must connect the router according to the following scheme:
- The provider's cable, coming from the switchboard in the entrance, is connected to the WAN port, which may be called “INTERNET”.
- The laptop is connected to one of the LAN ports of the router. By default, these 4 ports are equal if VLAN has not been previously configured on this DIR-300.
Reset
When connecting a used D-Link DIR-300, problems often arise with both non-working ports and logging into the GUI interface. To correctly configure such a router, you need to start by rolling back to factory settings: press the RESET button, which is located on the case near the power connector, and hold it for 15 - 20 seconds.
The RESET button is soldered directly to printed circuit board D-Link DIR-300, so you cannot apply excessive force when pressing: this will damage the router!
Restoring factory settings will also help if the router’s user settings are lost: the previously saved D-Link DIR-300 configuration should be loaded only after a rollback to the original settings.
A detailed description of how to restore the factory configuration is presented in
Computer settings
The computer from which the modem will be configured must receive its local address when turning on the power of the DIR-300. To do this you need to bring network card The PC is in automatic configuration mode.
1. Through the connection icon, which is located on the taskbar, you can go to the management network settings OS.
2. Then, go to properties local connection.
3. In the TCP/IPv4 properties, you need to check the “Automatic” checkbox.
Login to the router interface
To log in D-Link settings DIR-300, you need to dial network address router in Chrome or IE.
If the PC setup is done correctly, it will boot home page GUI of the router and a request for authorization in D-Link DIR-300 will appear.
If you encounter difficulties establishing a connection between your computer and the router, you should use.
Setting up an Internet connection
D-Link DIR-300 supports all types of connections made Russian providers. Before setting up the router, you need to prepare a contract in order to enter the credentials correctly.
Setting up a connection on the D-Link 300 can be done in two ways:
1. Automatically using the Click’n’Connect utility. This option is well suited for IPoE and PPPoE connection types;
2. Manual setting will be preferable to automatic for connections using a VPN server: L2TP and PPTP.
If you need to configure the D-Link DIR-300 router for providers, use these instructions.
Wi-Fi setup
D-Link DIR-300 is equipped wireless module N150 with 2 dBi antenna. In a small room, the router provides stable coverage. You can configure WiFi either manually or using the built-in utility or the WPS protocol.
- Manual configuration makes it possible to select the channel, speed mode and transmitter power, allowing you to fine-tune the router for specific operating conditions.
- The WPS protocol is supported by both TVs and mobile gadgets, connecting devices to D-Link 300 without entering a password.
- Automatic configuration of the router’s secure WiFi network is performed using the built-in “Wizard” of the D-Link DIR-300:
More detailed information how different ways performed WiFi setup D-Link 300 contains . It also provides recommendations for improving the coverage and wireless speed of the router.
Routing
Setting up a network is no longer the prerogative of geeks and IT specialists: a huge selection of devices has appeared on the market designed to make the life of an ordinary person better and more comfortable.
A home fleet of network devices can include a “PC + smartphone + iPad”, a media server, a game console, a TV, an IP camera and even a refrigerator, and the router is the heart home network. Setting it up means connecting these devices to the D-Link DIR-300 physically: with wires or via WiFi. And then ensure interaction between them and the Internet by establishing access and broadcast rules at the link and network levels.
The DIR-300 DHCP server distributes IP addresses to all devices and can operate in both dynamic and static modes. It is necessary to configure static addresses to register a route, since for this the router must associate a permanent local IP address with the MAC address of the specified device.
Configuring DHCP parameters in the D-Link D-300 is done on the “Network - LAN” tab. Here a pool of addresses is set and MAC/IP bindings are configured.
Setting up routing rules is available on the D-Link DIR-300 interface tab “Advanced - Routing”.
VLAN Configuration
Most of the new revisions of the D-Link DIR-300 modem support VLAN - a technology for dividing the network into logical segments. Configuration is performed on the “Advanced - VLAN” tab.
VLAN is used to group devices into target groups, optimize traffic and distribute access.
For example, you can allocate a child’s computer to a separate VLAN of the router and add a WiFi segment so that the child can connect a tablet or phone with his or her password to the D-Link DIR-300: no matter what device the connection is made from, this router setup will ensure viewing of protected content. filter.
The reason for using VLAN can also be the installation of an IPTV set-top box. If the provider supplies tagged traffic, then one of the interfaces D-Link router DIR-300 will have to be combined with a WAN port in transparent mode.
Port settings D-Link router DIR-300 in this scenario is described in the example of Rostelecom television.
Firewall and NAT
To set up remote access as home computer, and network storage connected to the DIR-300, you need to understand how the router implements network security mechanisms.
In a broad sense, under remote access refers to any traffic initiated from the outside towards the home network and router. Thus, to organize a gaming or FTP server After ensuring connection from remote machines, some configuration of the D-Link DIR-300 must be performed.
NAT is a mechanism that translates addresses so that Internet hosts do not see the real structure of the home network on the other side of the router, but process all traffic from local computers, seeing only the external WAN IP address. Thus, NAT in D-Link DIR-300 protects against network attacks, preventing direct access from outside to internal device addresses.
But at the same time, the router will interfere if you need to give friends access to FTP folders with photos or to the game space. To configure translation rules for NAT in the DIR-300, you need to perform port forwarding.
To configure the router ports, you need to go to the D-Link DIR-300 settings on the “Virtual Servers” tab.
+
There is one more problem: the router receives a gray WAN IP from the provider, which is constantly changing. Not having permanent address, connect to D-Link DIR-300 remote computer It won’t work, because the destination address is always different.
To solve this problem, DDNS technology is used, which allows you to assign a permanent IP to a dynamic IP. Domain name. The DDNS service updates information about WAN IP changes in real time and ensures continuous binding to the domain name.
Firewall is a set of rules for filtering traffic based on criteria such as address, port, protocol direction. Filtering by the D-Link DIR-300 firewall is carried out after decapsulation, routing and NAT processing.
The router allows you to reconfigure the firewall on the “Firewall - IP Filters” tab.
Network expansion
Wi-Fi router D-Link DIR-300 supports client mode. This means that either via cable or WiFi, you can connect the DIR-300 router to an upstream router to expand your existing network.
First you need to log in to the settings. In D-Link DIR-300, this function is located on the “WiFi - Client” tab.
The “Enable” checkbox switches the router to client mode, and the “Broadcast” option wireless network» allows you to connect WiFi devices to the D-Link DIR-300 as a repeater.
From the list of available networks, you need to select the corresponding SSID name of the upstream router and log in, and in the network parameters you set the name of the current network, password and encryption method.
If the WiFi password is changed on the upstream router, the D-Link DIR-300 client settings will have to be reinstalled. Therefore, in order for the router to work as a client without interruptions, it is recommended to fragment the WiFi network and use one of the segments as a bridge.
Now you need to configure the D-Link DIR-300 router modem so that devices connected to it as a client have access not only to local nodes, but also to the Internet.
On the DIR-300 “Network - WAN” tab, you need to specify the upstream direction of the WAN through the WiFi-Client interface and set the type of routing used in the local network.
Setting up the DIR-300 is accompanied by reboot notifications after each change to the configuration.
Found a typo? Select the text and press Ctrl + Enter
Loading...
