D link dir 300 nru Rostelecom connection. Creating a Wi-Fi connection

Step-by-step instruction how it is carried out setting up DIR-300. It starts with connecting the router.

Physical connection

• Turn on D-link DIR-300 into the outlet via the power supply.
• Install the cable from the Internet provider into the appropriate port of the router.
• Connect the computer and router with a wire (patch cord, i.e. blue cable).
• For Wi-Fi, screw on the antenna.

In the end, the wires on the back of the router should look something like this:




Setting up on PC

On a desktop computer connected via a wire, open Control Panel through Start, go to Network and Internet, then Network and Sharing Center and shared access, then go to Change adapter settings. See if your local network is turned on. Enable if it is disabled.




From now on, for the network to work, you don’t need to configure anything else on your computer. If any problems arise, perhaps you do not have a driver installed for your network card (or for Wi-Fi), please refer to our article on.

How to log in to the admin panel

You no longer need to configure the computer itself; the router stores all Internet settings within itself. But to set up the network you need to visit the router through the web interface. This can only be done via a wire, so you will have to log in either through a desktop PC with a wired connection, or connect a laptop/netbook via a LAN network to the router.

• Most often, the bottom of the DIR-300 contains the address of the local “site” with settings, as well as a login and password. Typically the address is 192.168.0.1.




• Enter it into your browser and you will go to the page generated by the router.




• The default login and password is admin.




Settings

Primary setup and path to basic Internet settings:

• You can immediately change the interface language.




• And set a password for the DIR-300 router. If you forget it, you will have to reset it, along with all settings, to “default”.




• To configure the Internet, go to the Advanced settings item below.




• In the Network block, follow the WAN link.




• Create a new connection; to do this, click the Add button in the lower right corner.




Basic network settings in the D-link DIR-300 router:



• Here you need to select the type of Internet connection. Usually this is PPPoE.
• You may have to clone the MAC address of your computer's network card into the router using the green arrow button (not always necessary, only if your ISP has a MAC address binding).
• Enter your Username and Password. This is the Internet access data from your provider (if you don’t know, look for it in your agreement with the provider).
• In other fields, you can leave everything as default and click the Save button.



• You will then be redirected to the previous page. The new connection you configured appears there. Check to see if the round check mark for this connection is set to Default Gateway.




• As a result, the Internet on a computer connected via LAN (i.e. by wire) should work. To check, go to any site:




• To prevent the settings from being reset, click Save on the router:




Congratulations, you have configured the Internet in the router and connected your computer to it via LAN.

Enabling WI-FI and setting up

To work via WiFi you need not only a laptop with an adapter wireless network, but also setting up a link router. You already know how to log into the router through a computer, do it.

• In Advanced Settings, find the WiFi section. Check that the green switch is in the on position. Just below, follow the link to Basic Settings.




• Check the Enable wireless connection checkbox and enter the name of the network. It will be displayed as the Wi-Fi name, which is visible to all devices (even those not yours) within the router's coverage area.




• Click change.



• We will be brought back, click Security Settings.



• Write down a password for Wi-Fi, otherwise anyone who catches it will be able to use it.




• Save the changes to the Wi-Fi settings on the DIR-300 router.




How to connect to Wi-Fi

If you configured the D-link router via a laptop/netbook using a wired connection, then you no longer need it. Disconnect the wire physically, and in Windows turn off “Connect via local network».

• Now turn on the Wireless network connection (it should be present if all drivers and software are present on Wi-Fi).



• A window with found WiFi networks will appear in the tray next to the clock. Remember what you called it in the router settings. Select and click Connect.



• Enter the password you set when setting up Wi-Fi D-link router DIR-300.




How to forward ports on a router

What is port forwarding? This is the port binding on external interface DIR-300 router with a device port on the local network. The idea is to give access to the device from the Internet using a specific open port router.

In practice it might look like this. There is a need to provide access to remote control slave. desktop PC connected to the Internet via the DIR-300 router (or another reason). To do this, a rule is created to redirect the WAN port to the port of the home PC.

To do this, go to the Advanced section, then to the Port Forwarding setting.
How to set up:




• Select a name for the rule (to avoid confusion, it is better to give meaningful names).
• Select a specific public port number or enter a range of ports). Public is an external port for the Internet. To register only one specific number, indicate it in the form of a starting and ending number.
• In the test example, we opened port 3389.
• Enter the IP address of the PC (server) to which the ports are forwarded. It is worth reserving this IP address for a specific computer in the DHCP reservation settings on the router, then it will not change over time. If you don’t want to make backups in the router, you can enter the IP address manually in the settings of the PC’s network card.
• The test example specified the internal gray IP address 192.168.1.100.
• Register the port for receiving incoming connections on a PC on the local network.
• For the test, we specified the default port 3389.
• Don't forget to check the box on the left to enable the rule.

Setting up IPTV

Setting up IPTV on routers: D-Link DIR-300, DIR-400, DIR-615 and DIR-655. Log in to the admin panel (instructions at the beginning of the article), you will see the main settings menu. Click Advanced, then Advanced Network. Specify the parameters:

• Check Enable Multicast Stream so that IPTV works via cable.
• Check the box for Wireless Enhance Mode to operate IPTV over Wi-Fi.
• We save with the “Save Settings” button (at the top of the page).

Perhaps the interface in your model will differ slightly from the picture shown.




If the specified menu items are not in the router, it may need to be flashed new firmware supporting IGMP proxy or Multicast Routing. Also note that the interface shown here is English, yours may be Russian.

How to turn on the router as a repeater

In order for the DIR-300 to work as a repeater, it needs to be flashed with the DD-WRT program.

• Version A1 is flashed via TFTP (so it is more difficult to make a repeater out of it).
• Version B1 can be flashed via the web interface.

Let's start setting up the repeater:

• We change the DIR-300 subnet to another one so that it differs from the main source point (for example, a laptop). If the laptop has 192.168.1.1, then here you need to make 192.168.2.1.
• DHCP can be enabled; to do this, select the IP of the main point (192.168.1.1) as a gateway.
• In the WAN settings item, go to Automatic-configuration DHCP and activate STP. Save.



Wi-Fi setup:

• In Wireless, select Mode – Repeater (or Repeater Bridge, if you have a different firmware version).
• The other remaining settings must match the source parameters (SSID, channel, connection type).
• The channel must be set to specific, not Auto. Security settings should also be similar to the source settings.
• Save.




After saving the settings, go to Status > Wireless > Site Survey, select the source point. Click the Connect button and save again. As a result, your router should receive the source IP and operate as a repeater.

Video settings on Rostelecom

Step-by-step video instructions for setting up D-Link DIR-300 for Rostelecom:

How to reset and reboot

To reset the settings to factory defaults, the router must be plugged in. After that, click the Reset button. It is recessed into the body to prevent accidental press, so you will need a toothpick. In some models, to reset you need to press Reset and hold for 15 seconds.




This will reset absolutely all settings, including the password (by default, like the login, it is admin).

How to reboot your router:

• Log in through the web interface and click Reboot.




• The router will reboot in 30-60 seconds, during which time you will be shown a message stating that it cannot be disconnected from the power supply.




• After this, the D-link DIR-300 is completely ready to work with the old settings.

Also, to reboot the router, you can physically disconnect it from the power outlet (preferably for 15-30 seconds).

Conclusion

You have learned how to configure the D-link DIR 300 router. And remember, the main ways to fix some problems with the router are to reboot and flash the firmware. Even if you have the most latest version firmware, then re-flashing can get rid of network glitches that have appeared (similarly).

To configure the Dlink DIR-300 D1 wifi router for the largest provider in Russia - Rostelecom, you do not need to call an installer or pay money at all. You can do everything yourself in 15-20 minutes and save 300-500 rubles. To set up, we may only need the login and password that you received after concluding the agreement. And then, if your Rostelecom branch uses the type PPPoE connections. If IPoE (i.e. Dynamic IP) is used, then all you need to do is configure the wireless network. But first things first.
After you have unpacked the router, you need to connect network cables as shown in the picture:

After you have connected your device to your computer, you need to go to the Network and Sharing Center. To do this you need to click right click mouse over the network icon in the form of a monitor on the taskbar and select the appropriate menu item:

You can also access the Network and Sharing Center from the Control Panel by selecting “Network and Internet” >>> “View network descriptions and tasks”:

Now you need to select the “Change adapter settings” link in the list on the right. This is how we get to " Network connections"Windows 7. In this list, you need to select the network connection through which your DIR-300 is connected, right-click on it and select “Properties”:

In the list of components, select “Internet Protocol Version 4” and click on the “Properties” button. The protocol properties window will open, where you need to check the boxes for automatically obtaining an IP address and DNS servers:

Click on “OK” and close the window. The network connection to the router is configured. Now you need to launch a web browser - better Internet Explorer or Google Chrome and in the address bar write the IP address of the router - . Press the Enter button and see the authorization request:

Login for access is admin, default password for access is admin. If the router is reset to factory settings, then you will be required to enter New Password for access.

After you have entered the web configurator, you need to decide how to proceed with setting up the D-Link DIR-300 router. And then if your connection type is “Dynamic IP”, then immediately proceed to setting up a wireless Wi-Fi network. The fact is that by default, D-Link routers are configured for this type of connection.

If your Rostelecom branch uses the PPPoE protocol for connection, then you need to select the menu item Network >>> WAN.

The connection there is - it must be deleted:

To do this, you just need to click on it, in the parameters window that opens, scroll the page to the very bottom - there will be a “Delete” button, which you need to click. After this, we return to the list of WAN connections and click on the “Add” button:

The window for creating a new connection will open:

In the “Main Settings” group, you need to select the “PPPoE” connection type. Please note that in the “Interface” list the value is “Internet” and the “Allow direction - WAN” checkbox is checked.

Below, in the “PPP” group, enter the login and password to connect to Rostelecom. Don't forget to check the "NAT" and " Firewall" Click on the “Apply” button.
Actually, that’s all - the connection has been created, the D-Link DIR-300 router has been configured to connect to the ISP network of the provider and the device should successfully connect to the Rostelecom network.

How to set up WiFi on DIR-300 D1

To set up a wireless Wi-Fi network on the Dlink Deer-300 router, you need to go to the section Wi-Fi >>> Basic settings:

In the “SSID” field you need to enter the name of the wireless network you are creating - this can be any word in English layout. The rest can be left at the default value - “Channel” in the “Auto” mode, and “Wireless mode” in mixed (802.11 B/G/N mixed). For 90% of users they will be optimal. Apply the settings.

Now you need to secure your network, for which we go to the section Security Settings:

The network authentication type must be set to “WPA2-PSK”.

If in the future there are problems with Android tablets and phones, try changing the type to “WPA-PSK/WPA2-PSK” or to “WPA-PSK”.

And then in the “PSK encryption key” field, enter the password to connect to your Wi-Fi. To do this, you need to use letters in the English layout, numbers and symbols. The password length is no shorter than 7-8 characters.
Click the “Apply” button. The WiFi wireless network has been created, configured and launched. You can connect clients!

P.S. Upon completion of manipulations with the settings, do not forget to save the settings of the D-Link DIR-300 router. This is done by clicking on the “System” icon at the top of the page. A menu will open in which you need to click on the “Save and Reload” button.

From time to time we encounter problems connecting to the Internet and IP television from the Rostelecom provider. Not many people know how to properly connect and then configure the device, which is why situations happen - a wireless network is detected and you can connect to it, but there is no access to the Internet.

The updated model largely repeats the design and functionality of the DIR-300 (vertical housing, built-in antenna), but the data transfer speed and signal level are slightly higher.

If you measure the data transfer speed, it will be in the range of 70-80 Mbit/s.

How to properly connect D-Link DIR-300 AD1

Oddly enough, there are many users in Russia who do not know how to properly connect a d-link router to a computer and start setting it up. This procedure is not complicated and intuitive, but it is enough to confuse the Lan and Internet ports to make further actions impossible.

Connecting Rostelecom Internet to your computer begins with examining the back panel of the router.

There are four sockets for wired connection of devices using the Internet or IPTV, and one socket for connecting a Rostelecom cable. In addition, there is a factory reset button, a power socket and an on/off button.

1. connecting the power plug;
2. connecting the Rostelecom cable to the socket yellow color with the signature “internet”;
3. The cable supplied with the router is connected to one of the four remaining sockets labeled “Lan” to connect it to the computer’s network card;
4. if you need to connect an IPTV set-top box, it is recommended not to rush to use it until the setup is completed;
5. the “On/Off” button is pressed and the computer is in automatic mode installs a driver to use the hardware.

How to enter the web interface of the D-Link DIR-300 AD1 modem parameters

Using the browser available on the computer (manufactured by D-link) or a self-purchased model dir-300 ad1. The setup procedure is similar, so it is not explained separately. 192.168.0.1 is entered into the site address input line - this is a link to the device’s web interface. After confirming the link, you will be able to log into the Rostelecom router.

Note: if the router is not new or you have already tried to configure it “for yourself,” then it may fail to receive authorization data. It is recommended to perform a factory reset. To do this, just take a paperclip or other thin object and press the “reset” button (holding for at least 20 seconds) next to the power supply socket.

If nothing happens when you request the web interface, then you need to go to the “Network Control Center...”. To do this, go to the tray icon wireless communication click with the left mouse button and select the desired item at the bottom, and then:

• Right-click on the active network card and bring up properties;
• in the list of components, select “protocol version 4” and open its parameters;
• by default, the items for obtaining DNS and IP addresses in auto mode should be checked;

After changing the parameters, the actions are confirmed with the “OK” button

To reconnect the Rostelecom Internet to your computer, enter the web interface address in the browser and when prompted for a password with the login in both cases, “admin”.

Fig.1. The interface should now appear
Fig.2. At the bottom right of the page, select the advanced configuration mode and click on the text “wan” in the “network” block

• In the page that opens, select “Dynamic IP” to change its parameters.
• Rostelecom wired Internet uses connection parameters - PPPoE, which are selected in the appropriate column.
• The login that was assigned to the user by the provider and written in the contract is used as the name.
• The connection password is also taken from there.
• Other parameters are not required to be changed.
• The changes made must be saved.
• The connection to the router will be lost on the computer, and then it will reappear.
• If you enter the parameters correctly, you will be able to use the Internet connection.

How to set up a WiFi network and IPTV on D-Link DIR-300 AD1

To connect home Internet Rostelecom via WiFi will need to go to the wireless network settings wizard in the modem’s web interface.

Here, the desired Wi-Fi network name (in Latin letters and numbers) is entered in the “SSID” field, and the encryption key field is the Rostelecom Wi-Fi password of 8 or more characters (numbers and Latin letters).

After entering, click the “next” button. The program will prompt you to select the connection port for the set-top box digital television IPTV. At the same time, the corresponding equipment is connected to the selected port. After this, the changes are saved and the Rostelecom Wi-Fi network appears available. If you were unable to connect Rostelecom to your computer on the first try, you can always reset the setting and repeat the steps.

WATCH THE VIDEO

This completes the setup of the D-Link DIR-300 AD1 router for Rostelecom. Ask questions to the experts.

D-Link DIR-300 NRU is one of the most popular routers among Russian users. Despite the fact that there is nothing complicated in setting up this router, sometimes it causes problems for novice users. In this manual, we will look at the process of setting up a router for the Rostelecom provider. Since the D-Link DIR-300 has several modifications and firmware, we will dwell in detail on the router settings for each firmware.

Important! Going into the router settings is very simple. Enter 192.168.0.1 in address bar your browser, login: admin, password: admin.

Getting ready to configure the dir-300 router

Most likely, before reading these instructions, you have already tried to configure the router yourself. Therefore, it would be a good idea to reset the dir-300 settings to factory settings. To do this, you need to plug in the router and hold the “reset” button on the back of the router for about 10 seconds (until all the indicators on the front panel blink). After this, it will take about 30 seconds to load the router. All settings will be reset to factory settings.

• In Windows 10, Windows 8, Windows 7, you need to go to the Network and Sharing Center (right-click on the local network icon in the taskbar). Then select “Change adapter settings”. Right-click on the network card and select “Properties”.

• In Windows XP, go to “Control Panel”, select “Network Connections”. Right-click on the network card and select “Properties”.
• You will see the connection properties window. Go to the settings of the item “Internet Protocol version 4 TCP/IPv4”
• The settings should be “Obtain an IP address automatically” and “Obtain a DNS server address automatically.” If not, make changes and click OK.

Let's move on to the next point.

Connection D-link Dir-300

There are 5 connectors on the back of the router. “LAN” connectors for connecting devices on your local network and an “Internet” connector for connecting your provider’s cable. You need to connect the provider cable to the “Internet” connector, and network card connect the computer from which you will configure the router to the LAN port (for example, the first one). If you have an IP-TV set-top box, connect it to LAN port 4. We plug the router into a power outlet.

How to go into the router settings and find out the firmware version

Today there are 2 types of current firmware for DIR-300. They differ in appearance and we will consider the process of setting up DIR-300 for Rostelecom for each of them. Going into the router settings is very simple. Open your favorite browser and enter the address of our router 192.168.0.1 into the address bar of the browser. After that, press “Enter”. Enter the login information: “username” – admin, “password” – admin.

After this, you will be asked to change the password from the administrative panel to your own. You do this, click “OK” and find yourself on the main page of the router settings. Depending on the firmware version, it will look like this.

First, we will look at the process of setting up the D-link DIR-300 router for Rostelecom for more new version firmware 14.x, and then for the older one - 1.3x. You can go straight to the part of the instructions you need. Alternatively, upgrade to a newer version from the D-Link website.

Setting up Rostelecom PPPoE DIR-300 connection for firmware 1.4.x

Click the “Advanced settings” button at the bottom of the page. If you have an English-language interface, you can change the language in the upper right corner of the page.

In the advanced settings window, select the “WAN” sub-item. A page will open with a list of current connections. Click on the “Dynamic IP” connection and delete it. Return to the list of connections and click “Add”. Next we will configure the Rostelecom PPPoe connection. You only need to specify the parameters that I will write about. Leave the rest as is.

PPPoE settings for Rostelecom on DIR-300 1.4.x

• Connection type – PPPoE
• Username – Your login from the Rostelecom agreement
• Password and password confirmation – Password from the Rostelecom agreement
• Click “Save”

If the settings are made correctly, the Internet will work after a short time.

You can proceed to setting up Wi-fi on the DIR-300.

Setting up Wi-Fi on DIR-300 with firmware 1.4.x

Let's go to home page settings of the DIR-300 router, select the sub-item “Wireless Network Setup Wizard” in the Wi-fi section. Next, using the “Wireless Network Setup Wizard,” you will step by step configure your wireless network settings. What needs to be changed:

• Click “Save”, then click “Save” in the upper right corner of the screen (where the light blinks)

This completes the wireless network setup for the DIR-300. You can use Wi-fi from a tablet, phone, laptop (from any Wi-fi-enabled device). To configure IP-TV, go to the end of the article.

Setting up Rostelecom PPPoE DIR-300 connection for firmware 1.3.x

So, in order to set up the Internet from Rostelecom on the specified DIR-300 firmware, we do the following:

• on home page router, click the “Configure manually” button
• On the “Network” tab, select “WAN”. Select the connection available there and select “Delete”.
• Return to the list of connections (it will be empty) and select “Add”

Now we need to configure the Rostelecom PPPoE parameters in our DIR-300 router.

We fill in only the following parameters, do not touch the rest:

• Connection type - PPPoE
• Username - Your login from the Rostelecom agreement
• Password and password confirmation - Password from the Rostelecom agreement
• Check the Keep Alive box if not checked.

Click “Save” and you will again find yourself in the list of connections. There will be a notification at the top of the page asking you to save your settings. Let's save them. If you did everything correctly, the status of the created connection will change to “Connected”. You can proceed to setting up your Wi-Fi wireless network.

Setting up Wi-Fi on DIR-300 with firmware 1.3.x

To configure Wi-Fi on the DIR-300, you need to go to the main page of the router settings, click “Configure manually”, select the “Wi-Fi” tab. Then go to the “Basic Settings” tab. We set the following parameters:

• SSID is the name of your wireless network. It will be visible to all Wi-fi users. Serves to identify your network by you and can be anything.
• Country – it is advisable to put “United States of America”. There will be fewer accessibility problems Wi-fi networks on different devices. If you are interested in why, ask in the comments.
• Click the “Change” button

Then go to the “security settings” tab to set a password for the Wi-fi network.

• Network authentication is undoubtedly WPA2-PSK, as the most secure.
• The PSK encryption key is yours Wi-fi password. The password requirements are at least 8 digits, letters are highly desirable.
• Click the “Change” button
• Do not ignore the notification about the need to save settings. Save the changes made.

On this Wi-fi setup for DIR-300 is completed. Try it, connect. Any Wi-Fi enabled device should work flawlessly. Let's move on to the IP-TV settings, if necessary.

Setting up IP-TV Rostelecom for DIR-300 (television)

Setting up IP-TV for firmware 1.3.x and 1.4.x is practically the same. On the initial page of the router, click “Set up IPTV” (if you have firmware 1.3.x) and “Wizard IPTV settings"if you have firmware 1.4.x. After this, you will need to specify the port to connect the IP-TV set-top box (the Internet will not work through this port). At the beginning of the article, I recommended connecting the set-top box to port 4. If you did this, specify port 4 and save the changes. On this IP-TV setup completed.

I hope you found it useful instructions on setup D-Link DIR-300 for Rostelecom.